Honeywell LYNX Touch Series User Manual

LYNX Touch Installation and Setup Guide
- 33 -
Programming the Control
Reporter
!
When Compass service is required and GSM or IP are the only reporting channels: As part of Primary Central
Station programming; the “Phone Type” must be set to any selection other than “None”, the “Communicator Type”
must be set to GSM or IP, as applicable, and must match the compass value; “Phone number” field must be left
blank and an “Account number” must be programmed.
The following system options are programmed in this section:
Option Function
Primar
y
or Secondary CS Info
Enroll information pertaining to the Primary and/or Secondary Central Station.
Phone Type Select the Report Format that will be used to send reports to the Primary or Secondary
Central Station, as applicable.
Phone Number Enter the Phone Number for the Primary or Secondary Central Station, as applicable.
Communicator Type Select the type of Communications Module that will be used to communicate with the
Primary or Secondary Central Station, as applicable.
Account Number Enter the account number for the Primary or Secondary Central Station, as applicable.
Dynamic Priority Select the primary method for sending Reports to the Primary or Secondary Central
Station, as applicable.
Dynamic Delay Selects delay between switching between reporting methods. Active if Dynamic Delay
feature has been set to Preferred Telco or Preferred Radio.
Report All Enable All Reports to be sent to the Primary or Secondary Central Station, as applicable.
Report Alarms Enable Alarm Reporting to the Primary or Secondary Central Station, as applicable.
Report Troubles Enable Trouble Reporting to the Primary or Secondary Central Station, as applicable.
Report Open/Close Enable Open/Close Reporting to the Primary or Secondary Central Station, as applicable.
Report Tests Enable Test Reporting to the Primary or Secondary Central Station, as applicable.
Follow Me Phone 1 or Phone 2
Enroll information Primary and/or Secondary telephone numbers for “Follow Me”
Announcements and/or Reminders.
Phone Type Enter Number for Follow Me Phone 1 or Phone 2, as applicable.
Phone Number Enter Primary and/or Secondary telephone numbers for “Follow Me” Announcements
and/or Reminders.
Report All Enable All Reports to be sent to the Follow Me Phone 1 or Phone 2, as applicable.
Report Alarms Enable Alarm Reporting to the Follow Me Phone 1 or Phone 2, as applicable.
Report Troubles Enable Trouble Reporting to the Follow Me Phone 1 or Phone 2, as applicable.
Report Open/Close Enable Open/Close Reporting to the Follow Me Phone 1 or Phone 2, as applicable.
Report Tests Enable Test Reporting to the Follow Me Phone 1 or Phone 2, as applicable.
Report Selection
Enable Reporting of Specific Events
Options
PBX Enter the digits required to access an outside line, if applicable
Call Wait Cancel Enter the digits required to cancel call waiting, if applicable
Number of Reports Limit the number of messages sent to the Central Station during an armed period.
(applies to LYNX Touch only)
Alarm Report Delay Disable or select the time delay for alarm reporting (applies to LYNX Touch only)
Swinger Shutdown Select the number of times reports are sent and sounder sounds for non-fire alarms
before the system ignores subsequent alarms (applies to LYNX Touch SIA only)
Abort Window Select the time delay for alarm reporting (applies to LYNX Touch SIA only)
First Offset Report Select the time for the first test report following power-up/programming or downloading
Report Frequency Select the test report frequency
Downloader
Phone Answer Enable or disable to allow control to answer incoming phone line.
Modem Speed (Future Use)
Ans. Machine Defeat Enable to defeat answering machine mode. (Active if Phone Answer is enabled.)
Ring Counter Enter the number of rings before control picks up phone line. (Active if Ans. Machine
Defeat is not enabled.)
Callback Number Enter the phone number the control will use to call back the downloading computer.
(Active if Phone Answer is enabled.)
Flexible Callback Allows Download operator to temporarily change the callback number by the number of
digits selected. Active if Phone Answer is enabled
Number Enter the number of flexible callback numbers that will be used. Active if Flexible
Callback is enabled.

Honeywell LYNX Touch Series Specifications

General

Brand	Honeywell
Model	LYNX Touch Series
Category	Security System
Language	English