Metso Valvcon ADC Series User Manual

18. ADCSERIES ACTUATORS BY MODEL NUMBER
Table 4
How To Order - ADC-Series Electric Actuators
(see note 1)
Actuator
Series
Enclosure Type
Torque Board Options
(see note 2)
Other Options
Operating
Voltage
Order
Code
Description Order
Code
Description Order
Code
Description Order Code Description Order
Code
Description
ADC W Weathertight 150 150 in-lb U2 On/O / Positioner Board I1
(
see note 3)
14mm Female Square Output
-UP
Universal
Power:
12/24 DC,
24AC, or
115/230AC
NEMA 4/4X 300 300 in-lb UL2 On/O / Positioner Board with Battery Back-Up
I2
(see note 3)
17mm Female Square Output
600 600 in-lb U4 On/O / Positioner Board 180-Degree
MB
(see note 4)
Modbus Communication
WX Weathertight &
Explosionproof
UL4 On/O / Positioner Board 180-Degree with Battery Back-Up
Y1
(see note 3)
15mm Female Keyed Output
NEMA 4/4X/7&9 U6 On/O / Positioner Board 270-Degree
Y2
(see note 3)
20mm Female Keyed Output
UL6 On/O / Positioner Board 270-Degree with Battery Back-Up Z Handwheel
LADC W Weathertight 1000 1000 in-lb U2 On/O / Positioner Board
I2
(see note 3)
17mm Female Square Output
-UP
Universal
Power:
12/24 DC,
24AC, or
115/230AC
NEMA 4/4X 1500 1500 in-lb UL3 On/O / Positioner Board with Battery Back-Up
I3
(see note 3)
19mm Female Square Output
2000 2000 in-lb U4 On/O / Positioner Board 180-Degree
I4
(see note 3)
22mm Female Square Output
WX Weathertight &
Explosionproof
2500 2500 in-lb UL5 On/O / Positioner Board 180-Degree with Battery Back-Up
MB
(see note 4)
Modbus Communication
NEMA 4/4X/7&9 3000 3000 in-lb U6 On/O / Positioner Board 270-Degree
Y2
(see note 3)
20mm Female Keyed Output
UL7 On/O / Positioner Board 270-Degree with Battery Back-Up
Y3
(see note 3)
25mm Female Keyed Output
Z Handwheel
Notes: 1. All ADC-Series actuators accept any of the following input voltages (12VDC, 24VDC, 24VAC, 115VAC and 230VAC), are rated for continuous duty
cycle, include a holding brake, two auxiliary limit switches, 4-20mA or 0-10VDC, position feedback, wrench-operated manual override, CSA “C US”
certication, CE compliance, and a heater/thermostat that can be user-enabled on the option board.
2. Must select only one board option; all board options can be congured for On/O or Modulating operation.
3. The standard drive output for 150 - 600 lb-in actuators is a 3/4” female square; the standard drive output for 1000 - 3000 lb-in actuators is a 1”
female square.
4. The Modbus Communication option allows for controlling, and polling the unit for diagnostic information using a Modbus communication signal
(RS-485; Two-Wire).
• Enclosure “W” (weathertight) is certified by CSA
to meet specifications for NEMA 4/4X; IP 66 for
weathertight and dust-tight, environments and is CE
compliant. It is intended for non-hazardous locations
in indoor or outdoor use.
• Enclosure “WX” (weathertight & explosionproof) is
certified by CSA to meet specifications for NEMA 7&9,
hazardous locations, (Class I, Division 1, Groups C, and
D; Class II, Division 1, Groups E, F, and G; Class III) as
well as to meet NEMA 4/4X and IP 66 specifications. the
enclosure is CE compliant, certified to ATEX directive
94/9/EC: Ex d IIB T6 Gb, and IECEx CSA 14.0057X.
Sample Model Code: ADCWX150UL2Y1-UP
Actuator Series ADC
Enclosure Type WX
Torque 150
Board Option UL2
Other Options
(if applicable)
Y1
Operating Voltage -UP
(For enclosure specifications and dimensions see Table 2
and Figure 26).
• Torque = Breakaway Torque Valvcon Electric Actuators
are rated at breakaway torque. This is the torque required
to move a full load immediately upon power-up.
Figure 27
IMO 6/18
IMO-I4900 EN 23

Metso Valvcon ADC Series Specifications

General

Brand	Metso
Model	Valvcon ADC Series
Category	Controller
Language	English