Appendices
A - 44
NX-series Communications Interface Units User’s Manual (W540)
The relationship between the unit versions of each Unit, EtherNet/IP Coupler Unit, CPU Unit and Indus-
trial PC, and versions of the Sysmac Studio and NX-
IO Configurator are shown below.
The items that are used in the version com
bination tables are given below.
The version combination ta
ble is given below.
• With the combinations of the unit versions/ver
sions shown below, you can use the functions that are
supported by the unit version of the Unit model. Use the unit versions/versions (or the later/higher
unit version/versions) that correspond to the NX Unit models and the unit versions. You cannot use
the specifications that were added or changed for the relevant NX Unit models and the unit versions
unless you use the corresponding unit versions/versions.
• Depending on the type and model of the Unit to which the NX
Unit is
connected, some Units do not
have the corresponding versions given in the table. If a Unit does not have the specified version, sup-
port is provided by the oldest available version after the specified version. Refer to the user’s manu-
als for the specific Units for the relation between models and versions.
• If you use the corresponding unit versions/versions given in the following table or later/higher ver-
sions, refer to the version information in the user
’s ma
nual for the Communications Coupler Unit,
CPU Unit, and Industrial PC.
A-6-2 Connection to an EtherNet/IP Coupler Unit
Relationship between Unit Versions of Units
NX Unit Corresponding unit versions/versions
Model
Unit
version
Application with an NJ/NX/NY-series Control-
ler
Application with a CS/CJ/CP-series PLC
EtherNet/IP
Coupler Unit
CPU Unit or
Industrial PC
Sysmac Stu-
dio
EtherNet/IP
Coupler Unit
Sysmac Stu-
dio
NX-IO Con-
figurator
Model
number
of NX
Unit
Unit ver-
sion of the
NX Uni
t
Uni
t version of
EtherNet/IP
Cou
p
ler Unit
that is compat-
ible with the
NX Unit
Unit version of
NJ/NX-series
CPU Uni
t or
NY-series
Industrial PC
that is compati-
ble with the
EtherNe
t/IP
Coupler Unit
Sysmac Stu-
dio version
that
is compat-
i
ble with the
N
X
Unit, Eth-
erNet/IP Cou-
pler Unit, CPU
U
nit, and
Industrial PC
Unit version of
EtherNet/IP
Coup
ler Unit
that is compat-
ible with the
NX Un
it
Sysmac Stu-
dio version
that is compat-
ible with the
NX Unit,
Eth-
erNe
t/IP Cou-
pler Unit, and
CPU Unit
NX-IO Config-
urator version
that is compa
t-
ib
le with the
NX Uni
t
, Eth-
erNet/IP Cou-
pler Unit, and
CPU Un
it
NX Unit Corresponding unit versions/versions
Model
Unit
version
Application with an NJ/NX/NY-series Con-
troller
*1
*1. Refer to the user’s manual for the EtherNet/IP Coupler Units for information on the unit versions of EtherNet/IP Units that
are compatible with EtherNet/IP Coupler Units.
Application with a CS/CJ/CP-series PLC
*2
*2. Refer to the user’s manual for the EtherNet/IP Coupler Units for information on the unit versions of CPU Units and
EtherNet/IP Units that are compatible with EtherNet/IP Coupler Units.
EtherNet/IP
Coupler
Unit
*3
*3. Serial communications instructions for CIF Units cannot be used if they are connected to an EtherNet/IP Coupler Unit.
CPU Unit or
Industrial PC
Sysmac Stu-
dio
EtherNet/IP
Coupler
Unit*
3
Sysmac Stu-
dio
NX-IO Con-
figurator
*4
NX-CIF101 Ver.1.0 Ver.1.2 Ver.1.14 Ver.1.19 Ver.1.2 Ver.1.19 Ver.1.00
NX-CIF105
NX-CIF210
To Next Page
Loading...
Need help?
General
