Onkyo TX-RZ50 User Manual

93
Playback
 Room EQ
Dirac Live (*1): You can select the equalizers measured with Dirac Live
( →p161, p165) from "Slot1" to "Slot3". When disabling the equalizer, select
"Off".
• The Dirac Live measurement results are saved in "Slot1" to "Slot3", but you
are able to register your own original sound quality with "Manual Adjust"
( →p166).
• This cannot be selected when measurements are made using "AccuEQ
Room Calibration".
AccuEQ (*1)(*2): Enable or disable the equalizer function that corrects for
sound distortion caused by the acoustic environment of the room.
On (All Ch): EQ that corrects according to the room acoustics acquired with the
AccuEQ calibration is applied to all channels.
On (ex. L/R): The same EQ as "On (All Ch)" is applied to speakers other than the
Front Speakers. EQ correction for the Front Speakers is turned off.
• The setting can be separately set to each input selector.
Manual Equalizer (*1)(*2): Select "Preset 1" to "Preset 3" congured in "2.
Speaker" - "Equalizer Settings" on the Setup menu. When this is set to "Off", the
same sound eld setting is applied to all ranges.
Re-EQ, Re-EQ(THX) (*1)(*2): Adjusts the soundtrack with the enhanced high
range so that it suits a home theater.
The following listening modes can be used for Re-EQ: Dolby Audio - DD, Dolby
Audio - DD+, Dolby Audio - Surr, Dolby Audio - TrueHD, Multichannel, DTS,
DTS-ES, DTS 96/24, DTS-HD High Resolution Audio, DTS-HD Master Audio,
DTS Neural:X, DTS Express and DSD
In Re-EQ(THX), the following listening modes can be used: THX Cinema and
THX Select Cinema.
EQ for Standing Wave (*1)(*2): Setting this "On" will control the effect of
the standing wave generated by the sound wave reected by wall or similar
interfering with the original sound wave.
(*1) It cannot be set if the listening mode is Pure Audio or Direct.
(*2) This function cannot be used if Dirac Live ( →p161, p165) is being used.
Furthermore, there is no effect even if it can be selected.
 Level
Front: Adjust the speaker level of the front speakers while listening to the sound.
Center: Adjust the speaker level of the center speaker while listening to the
sound.
Subwoofer: Adjust the speaker level of the subwoofer while listening to the
sound.
• If you set the unit to the standby mode, the adjustments you made will be
restored to the previous statuses.

Onkyo TX-RZ50 Specifications

General

Impedance	16 Ω
Receiver type	Surround
Frequency range	5 - 100000 Hz
Input sensitivity	200 mV
4Ω speaker support	Yes
Audio output channels	11.2 channels
Signal-to-Noise Ratio (SNR)	106 dB
Total Harmonic Distortion (THD)	0.08 %
Power output per channel (20-20KHz@8 Ohm)	250 W
AM band range	530 - 1710 kHz
FM band range	87.5 - 107.9 MHz
Supported radio bands	AM, FM
Preset stations quantity	40
AC input voltage	120 V
AC input frequency	60 Hz
Power consumption (standby)	0.1 W
Power consumption (typical)	850 W
HDMI in	6
USB ports quantity	1
Digital audio optical in	2
Multichannel audio input type	RCA
Component video (YPbPr/YCbCr) in	3
Connectivity technology	Wired
Speakers connectivity type	Clamp terminals
Wi-Fi	No
AirPlay	-
Display	LCD
Product color	Black
Audio decoders	DTS:X, Dolby Atmos
THX-certified	THX
Cables included	AC

Weight and Dimensions

Depth	201.5 mm
Width	435 mm
Height	398 mm
Weight	14000 g