Pioneer VSX-LX52 User Manual

Additional information
12
94
En
No sound
The unit does not respond
when the buttons are pressed.
• Try switching the receiver off, then back on again.
• Try disconnecting the power cord, then connect again.
AMP ERR blinks in the display,
then the power automatically
switches off. The ADVANCED
MCACC blinks and the power
does not turn on.
• The receiver may have a serious problem. Do not try switching the receiver on. Unplug the receiver
from the wall and call a Pioneer authorized independent service company.
The ADVANCED MCACC
indicator flashes and power
turns off.
• There is a problem with the receiver’s power unit. The receiver may have a serious problem. Unplug
the receiver from the wall and call a Pioneer authorized independent service company.
Multi-voltage model only: FAN
STOP blinks in the display,
then the power automatically
switches off.
• Something is obstructing the fan. Remove the obstruction and try switching the receiver back on.
If the fan is still not working, or you can’t remove the object, unplug the receiver from the wall and
call a Pioneer authorized independent service company.
• The fan is malfunctioning. Unplug the receiver from the wall and call a Pioneer authorized
independent service company.
AMP OVERHEAT and the
power indicator flash and the
power turns off.
• Allow the unit to cool down in a well-ventilated place before switching back on.
• Wait at least 1 minute, then try turning the power on again.
The Receiver suddenly power
off or the blue indicator at the
center of the receiver flashes.
• The power unit is damaged. Unplug the receiver from the wall and call a Pioneer authorized
independent service company.
Display blinks 12V TRG ERR.• An error has arisen in the 12 V trigger jacks. Reconnect accurately then turn the power back on.
Symptom Remedy
No sound is output when an
input function is selected.
No sound output from the front
speakers.
• Check the volume, mute setting (press MUTE) and speaker setting (press SPEAKERS).
• Make sure the correct input function is selected.
• Check that the MCACC setup microphone is disconnected.
• Make sure the correct input signal is selected (press SIGNAL SEL). Note that when PCM is
selected, you won’t be able to hear any other signal format.
• Check that the source component is connected properly (see Connecting your equipment on
page 14).
• Check that the speakers are connected properly (see Connecting the speakers on page 18).
No sound from the surround or
center speakers.
• C
heck that the Stereo listening mode or the Front Stage Surround Advance mode isn’t selected;
select one of the surround listening modes (see Listening in surround sound on page 51).
• Check that the surround/center speakers are not set to NO (see Speaker Setting on page 86).
• Check the channel level settings (see Channel Level on page 87).
• Check the speaker connections (see Connecting the speakers on page 18).
No sound from surround back
speakers.
• Check that the surround back speakers are set to LARGE or SMALL (see Speaker Setting on
page 86).
• Make sure surround back channel processing is set to SBch ON (see Using surround back channel
processing on page 54).
• If the source is Dolby Surround EX
or DTS-ES with no flag to indicate 6.1 compatibility, then with
surround back channel processing set to SBch Auto, there will be no sound from the surround back
speakers. In this case, set to SBch ON (see Using surround back channel processing on page 54).
• If the source does not have 6.1 playback channels, make sure that surround back channel
processing is set to SBch ON and a surround mode is selected (see Listening in surround sound on
page 51).
• Check the speaker connections (see Connecting the speakers on page 18).
If only one surround back speaker is connected, make sure it’s connected to the left channel speaker
terminal.
Symptom Remedy
VSX-LX52_DFLXJ.book 94 ページ ２００９年６月１日 月曜日 午前９時５９分

Pioneer VSX-LX52 Specifications

General

Brand	Pioneer
Model	VSX-LX52
Category	Receiver
Language	English