Sanyo PLC-SW30 User Manual

19
Connect the projector's AC Power Cord into an AC outlet. The
POWER indicator flashes in a moment and then turns red.
Press POWER ON-OFF button on the top control or the remote
control. The POWER Indicator turns green, and the cooling fans
start to operate. The starting display appears on the screen and
the count-down starts.
2
3
Tu r ning Off the Projector
Press the POWER ON-OFF button on the top control or the
remote control, and the message " Power off? " appears on the
screen.
Press the POWER ON-OFF button again to turn off the
projector. The POWER indicator starts to flash red and continues
while the cooling fans are operating. (for approx. 90 seconds)
1
2
TO MAINTAIN THE LIFE OF LAMP, ONCE YOU TURN
PROJECTOR ON, WAIT AT LEAST 5 MINUTES BEFORE
TURNING IT OFF.
DO NOT DISCONNECT THE AC POWER CORD WHILE
COOLING FANS ARE RUNNING OR BEFORE POWER
INDICATOR LIGHTS RED. OTHERWISE IT WILL RESULT IN
SHORTENING LAMP LIFE.
Tu r ning On the Projector
1
Complete peripheral connections (with a computer, VCR, etc.)
before turning on the projector.
3
When the projector is cooled down enough to be turned on
again, the Power indicator turns red again. Then you can
disconnect the AC power cord.
26
– The starting display disappears after 30 seconds.
– The starting display can be changed. (
☞
" Capture " P36 )
Power off?
Message disappears after 4 seconds.
Basic Operation
After the count-down, the input source that was selected last
and the Lamp mode status appear on the screen.
4
Note :
– When the Power Management function is ON, the projector detects signal
interruption and automatically turns off the projection lamp. (
☞ P 37 )
– The projector cannot be turned on during the cooling period with the
POWER indicator flashing red. You can turn it on again after the POWER
indicator lights red.
– Do not use the projector for more than 24 hours continuously. Turn off the
projector at least once in 24 hours and give it a rest. Continuous use may
result in shortening the lamp lifetime.
– This projector detects internal temperature and automatically controls the
running speed of the cooling fans.
– If the WARNING indicator flashes or lights red, see “Warning Indicator” on
page 42
(
☞
" Lamp mode " P37 )
Selected Input Source and Lamp Mode
Lamp mode

Sanyo PLC-SW30 Specifications

General

Native aspect ratio	4:3
Projection distance	- m
Vertical scan range	50 - 100 Hz
Horizontal scan range	15 - 80 kHz
Projection technology	3LCD
Contrast ratio (typical)	300:1
Screen size compatibility	34 - 200 \
Projector native resolution	SVGA (800x600)
Keystone correction, horizontal	20 °
Lamp type	UHP
Lamp power	150 W
Light source type	Lamp
Service life of light source	2000 h
Service life of light source (economic mode)	2500 h
RMS rated power	0.8 W
Number of built-in speakers	1
Power source	AC
AC input voltage	100 - 240 V
Power consumption (standby)	- W
Power consumption (typical)	244 W
Power consumption (PowerSave)	169 W
Focus	Manual
Throw ratio	1.6 - 1.9:1
Focal length range	- mm
Aperture range (F-F)	1.6 - 1.8
HDCP	-
Noise level	- dB
Dot clock scanning frequency	100 MHz
Full HD	No
Analog signal format system	NTSC, NTSC 4.43, PAL, PAL M, PAL N, SECAM
Supported graphics resolutions	800 x 600 (SVGA)
USB connector type	USB Type-B
HDMI ports quantity	0
Serial interface type	RS-232
USB 2.0 ports quantity	USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
Placement	Desktop
Product type	Standard throw projector
Product color	Black, White
Cables included	AC, VGA
Remote control type	IR

Weight and Dimensions

Depth	190 mm
Width	270 mm
Height	78 mm
Weight	2100 g