Sanyo PLC-SW30 User Manual

44
Tr oubleshooting
Before calling your dealer or service center for assistance, check the matters below once again.
– Make sure you have properly connected the projector to peripheral equipment as described in the section "Installation" on
P15-16.
– Make sure all equipment is connected to AC outlet and turned on the power.
– When you operate the projector with a computer, and it does not project an image, restart the computer.
No power.
– Plug the projector into your AC outlet.
– Make sure if the POWER Indicator lights red.
– Wait 90 seconds after a projector is turned OFF when turning the projector back on.
The projector can be turned on after the Power indicator turns red. (
☞
"Turning Off the
Projector " P19 )
– Check WARNING TEMP. indicator. If the indicator flashes red, the projector cannot be
turned on. (
☞
"Warning Indicator " P42 )
– Check the projection lamp. (
☞
P40-41 )
– Unlock Key lock for the projector in the Setting Menu. (
☞
P38 )
Image is out of focus.
– Adjust focus of the projector. (
☞
P20 )
– Provide proper distance between the projector and projection screen. (
☞
P13 )
– Check the projection lens to see if it needs cleaning. (
☞
P43 )
– Moving the projector from a cool temperature location to a warm temperature location may
result in moisture condensation on the projection lens. In such an event, leave the
projector OFF and wait until condensation disappears.
Picture is Left/Right
reversed.
– Check Ceiling / Rear feature. (
☞
“Setting” on page 37 )
Problem:
– Try these Solutions
Picture is Top/Bottom
reversed.
– Check Ceiling feature. (
☞
“Setting” on page 37 )
Some displays are not
seen during the
Operation.
– Check Display feature.(
☞
“Setting” on page 36 )
No image.
– Check the connection between your computer or video equipment and the projector.
– Check if the input signal is correctly output from your computer. Some laptop computers
may need to change the setting for monitor output when connected to the projector. See
the computer's owner's manual for its setting.
– Check NO SHOW function. (
☞
P21)
– When turning on the projector, it takes about 30 seconds to display an image.
– Check the system that you select is corresponding with your computer or video equipment.
– Select correct input source once again following the menu operation.
– Make sure the temperature is not out of the operating temperature range (5°C ~ 35°C).
No sound.
– Check audio cable connection from audio input source. (
☞
P15-16)
– Adjust the audio source.
– Press VOLUME (+) button.(
☞
P21)
– Press MUTE button. (
☞
P21)
Appendix

Sanyo PLC-SW30 Specifications

General

Native aspect ratio	4:3
Projection distance	- m
Vertical scan range	50 - 100 Hz
Horizontal scan range	15 - 80 kHz
Projection technology	3LCD
Contrast ratio (typical)	300:1
Screen size compatibility	34 - 200 \
Projector native resolution	SVGA (800x600)
Keystone correction, horizontal	20 °
Lamp type	UHP
Lamp power	150 W
Light source type	Lamp
Service life of light source	2000 h
Service life of light source (economic mode)	2500 h
RMS rated power	0.8 W
Number of built-in speakers	1
Power source	AC
AC input voltage	100 - 240 V
Power consumption (standby)	- W
Power consumption (typical)	244 W
Power consumption (PowerSave)	169 W
Focus	Manual
Throw ratio	1.6 - 1.9:1
Focal length range	- mm
Aperture range (F-F)	1.6 - 1.8
HDCP	-
Noise level	- dB
Dot clock scanning frequency	100 MHz
Full HD	No
Analog signal format system	NTSC, NTSC 4.43, PAL, PAL M, PAL N, SECAM
Supported graphics resolutions	800 x 600 (SVGA)
USB connector type	USB Type-B
HDMI ports quantity	0
Serial interface type	RS-232
USB 2.0 ports quantity	USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
Placement	Desktop
Product type	Standard throw projector
Product color	Black, White
Cables included	AC, VGA
Remote control type	IR

Weight and Dimensions

Depth	190 mm
Width	270 mm
Height	78 mm
Weight	2100 g