WEIHONG Ncstudio V15 User Manual

Name: WEIHONG Ncstudio V15
Brand: WEIHONG
Rating: 5 (1 reviews)

121 pages

To Next Page

To Previous Page

上海维宏电子科技股份有限公司

SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD.

68 / 116

5.2.8 GW SMATLas 3S Laser

The wiring diagram is shown below:

Table of Contents1
Quick Start4
Overview4
Hardware Connection Diagram4
Shortcut Keys6
Install the System7
Overview7
Install Follow-Up Amplifier7
Install Motion Control Card7
Install the Software7
Install the Drive8
Automatic Installation8
Manual Installation9
System Debugging10
Overview10
Configure Settings in Ncconfig10
Data Backup11
Data Restoration11
Device and Port Mapping Configuration11
Port Protection12
Modify I/O Port Polarity13
Set Drive Parameters13
Set Drive Parameters in Non-Bus Control Systems14
Set Drive Parameters in Bus Control Systems14
Set Bus System Parameters35
Set Speed Parameters35
Set Pulse Equivalent36
Check Axis Direction37
Set Workbench Travel Limits37
Set the Screw Error Compensation37
Set the Backlash Compensation38
Set the Bidirectional Compensation38
Check Machine Settings40
Pulse Equivalent and Electronic Gear Ratio40
Pulse40
Laser Technic Settings40
Do a Burn Test41
Install and Use the Camera42
Modify the Computer IP Address42
Modify the Camera IP Address42
Follow Debugging45
Overview45
Tab Area45
Coordinate Area45
Manual Control Area45
Follow Control Buttons45
Follow Control Area/Follow Parameter Setting Area45
Operations50
Prepare50
Measure the Capacitance50
Execute Servo Calibration50
Execute Calibration50
Check the Follow Function52
Follow Parameter52
System Setting52
Follow Setting52
Follow-Up52
Calibrate Setting52
Speed Setting52
Real-Time State Check53
Manual Speed53
Common Problems57
Serious Electric Interference57
Capacitance Is Not Zero When Touching the Material57
Cutter Continues Lowering after Touching the Material During Calibration57
Actual Follow Height Differs from Setting57
Cutter Stops Working Frequently When Capacitance Feedback and Calibration57
Results Are Normal59
Cutter Has Severe Jitters When Cutting Thin Plates and Causing Workpiece Outline Deformation59
System Reports Follow Error When Moving Z Axis or Enable Follow59
Encoder Direction or Axis Direction Error59
Follow In-Position Waiting Timeout60
Large Follow Error Alarm60
System Reports Material Collision Alarm When Follow Is Enabled in Idle Status or During Machining60
System Reports Material Collision Alarm When the System Has no Movement61
Follow Overshoot61
Wiring62
Controller and Terminal Board62
Lambda Controller62
Extension Terminal Board64
Laser66
IPG-YLR Series Laser66
Feibo MARS-500W Laser66
Raycus Fiber Laser68
JK / GSI-500W-FL Laser68
MAX Fiber Laser69
SPI-500W-R4 Laser70
HFB 1000-1500W Laser70
GW Smatlas 3S Laser71
Wiring Diagram of the Drive72
Drive Port Definition72
Wiring Diagram of the Drive (in Position Control Mode)74
Wiring Diagram of the Drive (in Velocity Control Mode)95
Wireless Handwheel111
Whb05L(V4)111
Whb05L(V5)113
Whb05N(V1)116
Specifications118
Precautions118
Faqs118
Legal Notices119
Requirements of Use119
Intellectual Property Rights Notice119
Termination119

WEIHONG Ncstudio V15 User Manual

Table of Contents

Questions and Answers:

WEIHONG Ncstudio V15 Specifications

Related product manuals

Brand	WEIHONG
Model	Ncstudio V15
Category	Control Systems
Language	English