EasyManuals Logo
Home>HP>Desktop>Z400

HP Z400 User Manual

HP Z400
254 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #213 background imageLoading...
Page #213 background image
POST error messages
The Power-On Self Text (POST) is a series of diagnostic tests that runs automatically when the
workstation is powered on.
Audible and visual messages occur before the operating system starts if the POST encounters a
problem. POST checks the following items to ensure that the workstation system is functioning properly:
ā—
Keyboard
ā—
DIMMs
ā—
Diskette drives
ā—
All mass storage devices
ā—
CPUs
ā—
Controllers
ā—
Fans
ā—
Temperature sensors
ā—
Cables (front/rear panels, audio, and USB ports)
The table shown next describes the POST error messages.
Table 6-10 POST error messages
Screen message Probable cause Recommended action
101—Option ROM Checksum
Error
System ROM checksum. Verify the you have the latest ROM:
1. Flash the ROM, if needed.
2. If an expansion card was recently added, remove
it to find out if the problem remains.
3. Clear CMOS. If the message disappears, there
might be a problem with the expansion card.
4. Replace the system board.
102—System Board Failure DMA, timers, and so forth, might be
set improperly or might be defective.
1. Clear the CMOS.
2. Remove the expansion boards.
3. Replace the system board.
110—Out of memory space
for option ROMs
Option ROM for a device could not
run because of memory constraints.
1. Run the Computer Setup (F10) Utility to disable
unneeded option ROMs, and to enable ACPI/
USB Buffers at Top of Memory.
162—Systems Options Error
163—Time and Date Not Set
ā—
Invalid time or date in
configuration memory.
ā—
RTC battery might need
replacement.
ā—
CMOS jumper might not be
properly installed.
1. Set the date and time from the Control Panel or in
the Computer Setup (F10) Utility (depending on
the operating system).
2. If the problem persists, replace the RTC battery.
ENWW
Diagnostic codes and errors
201

Table of Contents

Other manuals for HP Z400

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the HP Z400 and is the answer not in the manual?

HP Z400 Specifications

General IconGeneral
Bus typeQPI
Processor cache4 MB
Processor cores2
Processor modelW3503
System bus rate4.8 GT/s
Processor socket-
Processor frequency2.4 GHz
Processor cache typeSmart Cache
Processor lithography45 nm
Processor manufacturerIntel
PCI Express slots version2.0
Processor operating modes64-bit
ECC supported by processorYes
Thermal Design Power (TDP)130 W
Number of processors installed1
Memory types supported by processorDDR3-SDRAM
Memory clock speeds supported by processor800, 1066 MHz
Memory bandwidth supported by processor (max)25.6 GB/s
Maximum internal memory supported by processor24 GB
Audio systemRealtek ALC262
Product typeWorkstation
Motherboard chipsetIntelĀ® X58 Express
Memory slots6x DIMM
Internal memory4 GB
Memory channelsTriple-channel
Memory clock speed1066 MHz
Memory layout (slots x size)- GB
Graphics cardQuadro 600
Networking featuresGigabit Ethernet (10/100/1000)
Graphics card familyNVIDIA
HDD speed- RPM
RAID levels0, 1, 5, 10
HDD capacity500 GB
HDD interfaceSATA II
Storage mediaHDD
Display includedNo
USB 2.0 ports quantity8
Parallel ports quantity0
Chassis typeMinitower
Country of originChina
Number of 5.25\" bays3
Operating system installedWindows 7 Professional
Operating system architecture32-bit
Power supply475 W
Processor ARK ID40800
Processor package size42.5 x 45 mm
Supported instruction setsSSE4.2
Weight and Dimensions IconWeight and Dimensions
Depth455.3 mm
Width167.9 mm
Height450.2 mm
Weight13500 g

Related product manuals