HP Z400 User Manual

Copying a setup configuration to multiple workstations
CAUTION: A setup configuration is model-specific. If source and target workstations are not the
same model, file system corruption can result. For example, do not copy the setup configuration from
an HP xw8600 Workstation to an HP Z400 Workstation.
This method takes longer to prepare the configuration diskette, but copying the configuration to target
workstations is fast.
A bootable diskette is required for this procedure. If Windows XP is not available to create a bootable
diskette, use the method for copying to a single workstation instead (see
Copying a setup configuration
to a single workstation on page 45).
1. Create a bootable diskette or USB media device.
2. Select a setup configuration to copy.
3. If you are using a diskette or USB storage device, insert it now.
4. Restart the workstation.
5. As soon as the workstation powers on, press and hold F10 until you enter the Computer Setup
(F10) Utility. If necessary, press Enter to bypass the title screen.
NOTE: If you do not press the F10 key at the appropriate time, you must restart the workstation,
and then press and hold the F10 key again to access the utility.
If you are using a PS/2 keyboard, you might see a keyboard error message. Disregard it.
6. Select File>Replicated Setup>Save to Removable Media, and follow the instructions on
the screen to create the configuration diskette or USB media device.
7. Download a BIOS utility for replicating setup (repset.exe), and copy it to the configuration diskette
or USB media device. To obtain this utility, see
http://www.hp.com/support/files.
8. Enter the model number of the workstation.
9.
On the configuration diskette, create an autoexec.bat file containing repset.exe and cpqsetup.txt.
10. Power off the workstation you are configuring, insert the configuration diskette or USB device, and
then power on the workstation. The configuration utility runs automatically.
11. When the configuration is complete, restart the workstation.
46 Chapter 4 System management ENWW

HP Z400 Specifications

General

Bus type	QPI
Processor cache	4 MB
Processor cores	2
Processor model	W3503
System bus rate	4.8 GT/s
Processor socket	-
Processor frequency	2.4 GHz
Processor cache type	Smart Cache
Processor lithography	45 nm
Processor manufacturer	Intel
PCI Express slots version	2.0
Processor operating modes	64-bit
ECC supported by processor	Yes
Thermal Design Power (TDP)	130 W
Number of processors installed	1
Memory types supported by processor	DDR3-SDRAM
Memory clock speeds supported by processor	800, 1066 MHz
Memory bandwidth supported by processor (max)	25.6 GB/s
Maximum internal memory supported by processor	24 GB
Audio system	Realtek ALC262
Product type	Workstation
Motherboard chipset	Intel® X58 Express
Memory slots	6x DIMM
Internal memory	4 GB
Memory channels	Triple-channel
Memory clock speed	1066 MHz
Memory layout (slots x size)	- GB
Graphics card	Quadro 600
Networking features	Gigabit Ethernet (10/100/1000)
Graphics card family	NVIDIA
HDD speed	- RPM
RAID levels	0, 1, 5, 10
HDD capacity	500 GB
HDD interface	SATA II
Storage media	HDD
Display included	No
USB 2.0 ports quantity	8
Parallel ports quantity	0
Chassis type	Minitower
Country of origin	China
Number of 5.25\" bays	3
Operating system installed	Windows 7 Professional
Operating system architecture	32-bit
Power supply	475 W
Processor ARK ID	40800
Processor package size	42.5 x 45 mm
Supported instruction sets	SSE4.2

Weight and Dimensions

Depth	455.3 mm
Width	167.9 mm
Height	450.2 mm
Weight	13500 g