EasyManua.ls Logo

Quantum DXi V-Series User Manual

Quantum DXi V-Series
140 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #121 background image
Quantum DXi-Series Command Line Interface (CLI) Guide
6-67081-09 Rev B
February 2014
Network CLI Commands 111
DXi 6540 With Only Two Independent Ports Being Used
DXi 6540 With Three Bonds of Two Ports Each
DXi 6540 With One Bond and Two Independent Interfaces
DXI 6540/6550 With All Customer Interfaces Used Independently
Deleting a Bond and Setting Up Independent Interfaces
DXi 6540 Connected to Two Different Networks Through Two Bonds
The bonded interfaces on the DXi are connected to two different subnets; this
may have two different default gateways for the subnet.
Figure 1 Netcfg Example – Two
Data Networks
The following syscli sequences can be used to configure a similar setup.
To display the existing configuration:
syscli --list interface
First, delete the default bond configuration with all customer ports connected
together:
syscli --del netcfg --devname bond0
Then configure bond0 and use this bond IPADDR, if applicable configure the
GATEWAY1:
syscli --add netcfg --devname bond0:1 --slaves eth0, eth1
--segments DATA,REP --ipaddr IPADDR1 --netmask NETMASK1
--gateway GATEWAY1

Table of Contents

Question and Answer IconNeed help?

Do you have a question about the Quantum DXi V-Series and is the answer not in the manual?

Quantum DXi V-Series Specifications

General IconGeneral
Data DeduplicationYes
Deduplication RatioUp to 20:1
ReplicationYes
InterfaceEthernet
EncryptionYes
Supported ProtocolsCIFS, NFS, VTL
ManagementWeb-based GUI, CLI

Summary

Introduction to Quantum DXi CLI

CLI Users and Access

Describes the two local CLI user accounts, cliadmin and cliviewer, and their capabilities.

VTL Configuration CLI Commands

Adding a Virtual Tape Library (VTL)

Guides on adding a VTL partition with settings like name, model, slots, drives, and deduplication.

Creating Media for VTL

Guides on creating media for a defined VTL, requiring VTL name, type, number of media, and starting barcode.

Moving Media Between Storage Locations

Describes how to move media between virtual storage locations using source and destination types and indices.

NAS Configuration CLI Commands

Adding a NAS Share

Guides on adding one or more NAS shares with options for name, protocol, description, and permissions.

Joining or Disjoining Windows Domain

Covers joining a server to a workgroup or Active Directory domain and disjoining.

CIFS Share Access Control

Manages workgroup user access to CIFS shares and provides limited domain user privilege grants.

Replication CLI Commands

Initiating Replication for VTL or NAS

Starts replication for a specified VTL or NAS share, with options for barcode or namespace.

Failback VTL to Source from Target System

Fails back a replicated VTL to its specified source system.

Enabling VTL Replication Options on Source

Enables replication for a specified VTL on the system as a source.

OST CLI Commands

Adding a Storage Server

Adds a storage server with options for name, max connections, and description.

Installing TLS Certificate Files

Installs user-provided Transport Layer Security (TLS) certificate files for encryption.

Network CLI Commands

Adding Network Configurations

Adds and configures network devices with IP, netmask, and gateway.

Setting Host, Domain Names, and DNS Search Path

Sets the system's host name, domain name, and DNS search paths.

Status CLI Commands

Getting VTL Performance Status

Returns the VTL's average write speed.

Health Check CLI Commands

Starting a Health Check

Starts a healthcheck on the system if it is not running.

Related product manuals