EasyManuals Logo

Yaesu FT-2000D User Manual

Yaesu FT-2000D
140 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #83 background imageLoading...
Page #83 background image
Page 81FT-2000D OPERATING MANUAL
TRANSMITTER CONVENIENCE FEATURES
SPLIT-FREQUENCY OPERATION
1. Start with regular transceiver op-
eration on the Main (VFO-A) band.
MAIN (VFO-A)
[
RX
]
switch “ON”
(LED glows Green)
[
TX
]
switch “ON”
(LED glows Red)
SUB (VFO-B)
[
RX
]
switch “OFF” (LED Off)
[
TX
]
switch “OFF” (LED Off)
2. Press and hold in the
[
SPLIT
]
button for two sec-
onds to engage the Quick Split feature, and apply a
frequency 5 kHz above the Main (VFO-A) fre-
quency to the Sub (VFO-B) frequency register.
The VFO configuration will then be:
MAIN (VFO-A)
[
RX
]
switch “ON” (LED glows Green)
[
TX
]
switch “OFF” (LED Off)
SUB (VFO-B)
[
RX
]
switch “OFF” (LED Off)
[
TX
]
switch “ON” (LED glows Red)
3. Press and hold in the
[
SPLIT
]
button for two sec-
onds to increment the Main (VFO-A) frequency
another +5 kHz.
QUICK POINTS:
The operating mode applied to the Sub (VFO-B)
register will be the same as that in use on the Main
(VFO-A) register.
The offset of the Sub (VFO-B) from the Main VFO
(VFO-A) is programmed via the Menu, and is set
to +5 kHz at the factory. Other offsets may be se-
lected, however, using the following procedure:
1. Press the
[
MENU
]
button to enter the Menu mode.
2. Rotate the Main Tuning Dial knob to select Menu
item “033 GEnE Q SPLIT.”
3. Rotate the
[
SUB VFO-B
]
knob to select the de-
sired offset.
The available selections are
–20kHz–20kHz
–20kHz–20kHz
–20kHz ~
+20kHz+20kHz
+20kHz+20kHz
+20kHz
(factory default:
+5 kHz+5 kHz
+5 kHz+5 kHz
+5 kHz).
4. When you have completed all adjustments, press
and hold in the
[
MENU
]
button for two seconds to
save the new setting and exit to normal operation.
If you only press the
[
MENU
]
button momentarily
to exit, any changes you performed will not be
stored.
[
SPLIT
]
Button
MAIN
[
TX
]
Switch
Sub
[
RX
]
Switch
MAIN
[
RX
]
Switch
Sub
[
TX
]
Switch
Main Tuning Dial Knob
[
SUB VFO-B
]
Knob
[
MENU
]
Button
Quick Split Operation
The Quick Split feature allows you to set a one-touch offset of +5 kHz to be applied to your radio’s transmit
frequency on the Sub (VFO-B), compared to the Main (VFO-A) frequency.
WXWXWXWXWXWXWXWXWXWZYXWZYXWZYXWZYXWZYXWZYXWZYXWZYXWZYXWZYXWZYXWZYXWZYXWZYXWZYX

Table of Contents

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Yaesu FT-2000D and is the answer not in the manual?

Yaesu FT-2000D Specifications

General IconGeneral
BrandYaesu
ModelFT-2000D
CategoryTransceiver
LanguageEnglish

Related product manuals