Fort VISION User Manual

32
DESCRIPTION OF FIGURES
Fig. 1/A and 1/B - Multipurpose machine Mod. VISION
- Main parts.
1) Right track (in a position that is NOT reversible);
2) Footrest footrest;
3) PTO engagement control lever;
4) Motor unit (for the type of motor and its cha-
racteristics, see the enclosed instruction book-
let);
5) driver's seat with operator safety system pre-
sent;
6) Seat belt;
7) Roll-bar (upper mobile part);
8) Roll-bar (lower xed part);
9) Attack third upper point;
10) Left track (in a position that is NOT reversible);
11) Rapid change of power take-off interchangeable
equipment;
12) Emergency stop button. Pressed it blocks the
multipurpose machine in the position in which
it is located;
13) Lever available for auxiliary controls. This com-
mand must be used for optional hydraulically
operated equipment (with the prior consent of
the Manufacturer);
14) Front hydraulic lift control lever;
15) Digital display;
16) Electric start key;
17) Lift down speed regulator;
18) Accelerator lever
19-23) Display indications (see paragraph 1.4.2);
24) Parking brake lever;
25) Hydraulic oil tank lling cap;
26) Hydraulic oil drain plug;
27) Hydraulic oil level indicator light;
28) "Air" enrichment control device;
29) Manettino for starting the engine by tearing
(with the consent given by the electric start key).
30) bumper;
31) Fuel tank ller cap;
32) Right track control lever;
33) Left track control lever;
34) Release knob for seat rotation;
35) Document compartment;
36) Production batch identication plate;
37) EC model identication plate;
38) Label with serial number;
39) Engine rpm selection button / RPM speed Km / h
Fig. 2 - Lifting of the machine and its attachment
points.
ENGLISH
TABLE OF CONTENTS
SECTION 1. Description and characteristics of the
multipurpose machine
1.1 Introduction.................................................... 33
1.2 Warranty ........................................................ 34
1.2.1 Warranty exclusions ....................................... 34
1.3 Machine identication .................................... 34
1.4 Machine description and intended use ........... 34
1.4.1 Control and command station ........................ 35
1.4.2 Digital display (Optional) ................................ 35
1.5 Interchangeable equipment ............................ 35
1.6 Guards and safety devices .............................. 36
1.6.1 Noise risk ....................................................... 36
1.6.2 Vibration level................................................. 36
1.7 Technical features .......................................... 36
SECTION 2. Safety and prevention
2.1 Safety ............................................................. 37
2.1.1 Terminology used........................................... 37
2.1.2 General safety standards ................................ 37
2.2 Safety signs .................................................... 37
2.3 Warnings for operating
interchangeable equipment ............................ 38
2.4 Safety in the use and maintenance ................. 38
SECTION 3. Transport
3.1 Transport........................................................ 39
SECTION 4. Use
4.1 Before use ...................................................... 40
4.2 Start-up ......................................................... 40
4.3 Equipment connection .................................... 42
4.4 Reversibility.................................................... 42
4.5 During work ................................................... 43
4.5.1 Using the machine on slopes ......................... 43
4.5.2 Parking ........................................................... 43
4.6 Stop................................................................ 43
4.7 After use ......................................................... 44
SECTION 5. Maintenance
5.1 General data ................................................... 44
5.2 Routine maintenance ...................................... 44
5.2.1 Hydraulic oil replacement ............................... 44
5.2.2 Tracks ............................................................ 44
5.2.3 Battery ............................................................ 44
5.3 Motor maintenance ........................................ 44
5.4 Extraordinary maintenance ............................. 48
5.5 Rest ................................................................ 48
5.6 Dismantling the machine ................................ 48
5.7 Spare parts ..................................................... 48
5.8 Inconveniences and troubleshooting .............. 48
Attached: Wiring diagram (Briggs & Stratton) .......... 51
Declaration of conformity .......................................... 75

Fort VISION Specifications

General

Brand	Fort
Model	VISION
Category	Tractor
Language	English