Kenwood C-V751 User Manual

10
System connection
OPEN/CLOSE
Note
Note
Opening/closing the door
When opening or closing the door, be careful not to catch
your finger in the door. Otherwise there is a risk of injury.
Changing the input selection display (AUTO key)
To make the system control operation, the input selection display should be switched according to the actually connected components.
About the system control connections
8
Each press switches the indication.
1 Select “DVD” with the INPUT SELECTOR .
Main unit
GRC
INPUT
EMO AUTO BAN
D
3 Press and hold the AUTO key for more
than 2 seconds, until “DVD 6ch” is
displayed. (Main unit only)
m
o
v
i
e
To change the DVD display into the DVD 6CH display or LD display.
Analog input
Each press switches the indication.
Digital input
1 DVD 2 LD
2 Press the INPUT MODE key.
INPUT MODE
l
i
s
t
e
n
m
o
d
e
Select the “Input Analog” icon.
1 Press the ON/STANDBY key to ON.
ON/STANDBY
2 Opening/closing the door
1 DVD 2 DVD 6ch 3 LD
Using DVD 6ch INPUT

Kenwood C-V751 Specifications

General

harmonic distortion	0.01 %
signal to noise ratio	93 dB
sensitivity / impedance	200 mV / 47kΩ
controls S	± 10 dB (at 100 Hz)
BLE	± 10 dB (at 10 kHz)
level / impedance E REC	200 mV / 1 kΩ
composite	1 Vp-p/75 Ω
sampling frequency	32 kHz, 44.1 kHz, 48 kHz
input (coaxial)	0.5 Vp-p/75 Ω
optical	-15 dBm~-21 dBm, 600 nm ± 30 nm
frequency range	87.5 MHz~108 MHz
sensitivity (DIN) O	1.2 µV (at 75 Ω) / 13.2 dBf (40 kHz dev., S/N 26 dB)
sensitivity (DIN) REO	35 µV (at 75 Ω) / 42 dBf (46 kHz dev., S/N 46 dB)
signal to noise ratio (DIN weighted at 1 kHz, 40 kHz dev.) O	65 dB (65.2 dBf input)
signal to noise ratio (DIN weighted at 1 kHz, 40 kHz dev.) REO	60 dB (65.2 dBf input)
sensitivity (DIN ± 300 kHz)	64 dB
separation (DIN, 1 kHz)	36 dB
frequency response	30 Hz~15 kHz, + 0.5 dB, – 3.0 dB
tuning frequency range	531 kHz ~ 1, 602 kHz
usable sensitivity (30% mod., S/N 20 dB)	20 µV / (700 µV / m)
signal to noise ratio (at 30% mod. 1mV input)	48 dB
tuning frequency range	531 kHz ~ 1, 602 kHz
usable sensitivity (30% mod., S/N 20 dB)	20 µV / (700 µV / m)
signal to noise ratio (at 30% mod. 1mV input)	48 dB
tuning frequency range	153 kHz ~ 279 kHz
usable sensitivity (30% mod., S/N 20 dB)	35 µV
signal to noise ratio (at 30% mod. 1mV input)	45 dB
power consumption	35 W
dimensions (W x H x D)	400 mm x 105 mm x 382 mm
weight (net)	5.2 kg
weight (net) (For Australia)	5.1 kg