Kenwood C-V751 User Manual

57
Timer operation
MULTI.CONTROL
LEVEL
TIMER
SET
TIMER
SET
MULTI.CONTROL
LEVEL
TIMER
SET
MULTI.CONTROL
LEVEL
MULTI.CONTROL
LEVEL
TIMER
SET
MULTI.CONTROL
LEVEL
TIMER
SET
TIMER
MODE
Make the desired reservation.
1 Select the mode.
For timer playback Timer recording of broadcasts
1 Select “PLAY”
(Each press alternates them.)
PLAY : At the ON time, playback starts.
REC
Down
Up
2 Select the input source.
2 Enter it.
Down
Up
1 Select the source to be played.
(Each press switches the following).
1 TUNER
2 CD
3 MD/TAPE 1
4 DVD/DVD 6ch INPUT
2 Enter it.
3 Select the broadcast station (only when TUNER is selected above).
1 Select the preset station No.
2 Enter it.
Down
Up
÷ The station to be received with timer must be preset beforehand.
‚qw
Activating the timer
Select the TIMER No.to be used.
Each press of the key switches the TIMER numbers as follows.
÷ The selected TIMER No. lights.
÷ The timer will not function unless a TIMER No. is selected.
1 Select the mode.
1 Select “REC”.
(Each press alternates them.)
PLAY
REC
Down
Up
2 Enter it.
2 Select the broadcast station.
1 Select the preset station
No.
Down
Up
2 Enter it.
Main unit
Main unit
Main unit
KHz TIMER 1 2 TAP
E
FM
LW
MW
AUTO SOUND
O
D
S
PRO LOGIC
DIGI
T
3
AM
MHz SLEEP
DO
W
DIGI
T
DTS DOLBY
DIGI
T
PLAY
KHz TIMER 1 2 TAP
E
FM
LW
MW
AUTO SOUND
EREO
U
NED
TP
N
EWS
L
IP
PRO LOGIC
DIGI
T
3
AM
MHz SLEEP
DO
W
DIGI
T
DTS DOLBY
DIGI
T
TUN
E
R
KHz TIMER 1 2 TAPE2
/
FM
LW
MW
AUTO SOUND
R
EO
ED
P
W
S
P
PRO LOGIC
DIGIT
A
3 S
T
AM
MHz SLEEP
DOW
N
DIGIT
A
DTS DOLBY
DIGIT
A
) 1
89. ))
8
Display when TUNER is selected
1 TIMER 1 ...... Execution of timer 1 only.
2 TIMER 2 ...... Execution of timer 2 only.
3 TIMER 1, 2 .. Execution of timers 1 and 2.
4 Off
Continued to next page
Activating the timer
1
The reservation contents cannot be cleared. The contents are cleared only when they are
changed.

Kenwood C-V751 Specifications

General

harmonic distortion	0.01 %
signal to noise ratio	93 dB
sensitivity / impedance	200 mV / 47kΩ
controls S	± 10 dB (at 100 Hz)
BLE	± 10 dB (at 10 kHz)
level / impedance E REC	200 mV / 1 kΩ
composite	1 Vp-p/75 Ω
sampling frequency	32 kHz, 44.1 kHz, 48 kHz
input (coaxial)	0.5 Vp-p/75 Ω
optical	-15 dBm~-21 dBm, 600 nm ± 30 nm
frequency range	87.5 MHz~108 MHz
sensitivity (DIN) O	1.2 µV (at 75 Ω) / 13.2 dBf (40 kHz dev., S/N 26 dB)
sensitivity (DIN) REO	35 µV (at 75 Ω) / 42 dBf (46 kHz dev., S/N 46 dB)
signal to noise ratio (DIN weighted at 1 kHz, 40 kHz dev.) O	65 dB (65.2 dBf input)
signal to noise ratio (DIN weighted at 1 kHz, 40 kHz dev.) REO	60 dB (65.2 dBf input)
sensitivity (DIN ± 300 kHz)	64 dB
separation (DIN, 1 kHz)	36 dB
frequency response	30 Hz~15 kHz, + 0.5 dB, – 3.0 dB
tuning frequency range	531 kHz ~ 1, 602 kHz
usable sensitivity (30% mod., S/N 20 dB)	20 µV / (700 µV / m)
signal to noise ratio (at 30% mod. 1mV input)	48 dB
tuning frequency range	531 kHz ~ 1, 602 kHz
usable sensitivity (30% mod., S/N 20 dB)	20 µV / (700 µV / m)
signal to noise ratio (at 30% mod. 1mV input)	48 dB
tuning frequency range	153 kHz ~ 279 kHz
usable sensitivity (30% mod., S/N 20 dB)	35 µV
signal to noise ratio (at 30% mod. 1mV input)	45 dB
power consumption	35 W
dimensions (W x H x D)	400 mm x 105 mm x 382 mm
weight (net)	5.2 kg
weight (net) (For Australia)	5.1 kg