Kenwood C-V751 User Manual

63
NotesNotes
Notes
Specifications
Caution : Read this page carefully to ensure safe operation.
For C-V751
Audio section
Total harmonic distortion (1 kHz, 1V)
...................................................................................... 0.01 %
Signal to noise ratio (IHF’66)
CD .................................................................................. 93 dB
Input sensitivity / impedance
CD .................................................................. 200 mV / 47kΩ
Tone controls
BASS ...................................................... ± 10 dB (at 100 Hz)
TREBLE .................................................. ± 10 dB (at 10 kHz)
Output level / impedance
TAPE REC ..................................................... 200 mV / 1 kΩ
Video section
VIDEO inputs / outputs
(composite) ....................................................... 1 Vp-p/75 Ω
Digital section
Sampling frequency
......................................................... 32 kHz,44.1 kHz,48 kHz
Digital input
(coaxial) .......................................................... 0.5 Vp-p/75 Ω
(optical) ..................... -15 dBm~-21 dBm, 600 nm ± 30 nm
FM Tuner section
Tuning frequency range ......................... 87.5 MHz~108 MHz
Usable sensitivity (DIN)
MONO ........................................ 1.2 µV (at 75 Ω) / 13.2 dBf
(40 kHz dev., S/N 26 dB)
STEREO ......................................... 35 µV (at 75 Ω) / 42 dBf
(46 kHz dev., S/N 46 dB)
Signal to noise ratio (DIN weighted at 1 kHz, 40 kHz dev.)
MONO ............................................... 65 dB (65.2 dBf input)
STEREO ............................................ 60 dB (65.2 dBf input)
Selectivity (DIN ± 300 kHz) ........................................... 64 dB
Stereo separation (DIN, 1 kHz) .................................... 36 dB
Frequency response .......... 30 Hz~15 kHz, + 0.5 dB, – 3.0 dB
MW Tuner section
Tuning frequency range ........................ 531 kHz ~ 1,602 kHz
Usable sensitivity
(30% mod., S/N 20 dB) ..................... 20 µV / (700 µV / m)
Signal to noise ratio
(at 30% mod. 1mV input) .......................................... 48 dB
LW Tuner section
Tuning frequency range ........................... 153 kHz ~ 279 kHz
Usable sensitivity
(30% mod., S/N 20 dB) .............................................. 35 µV
Signal to noise ratio
(at 30% mod. 1mV input) .......................................... 45 dB
General
Power consumption ........................................................ 35 W
AC outlet
UN SWITCHED (for Australia) ........... 1: (Total 100 W max)
UN SWITCHED (except Australia) .... 2: (Total 100 W max)
Dimensions....................................... W: 400 mm (15-3/4”)
.......................................... H: 105 mm (4-1/8”)
.......................................... D: 382 mm (15-1/16”)
Weight (net) .................................................... 5.2 kg (11.4 lb)
Weight (net) (For Australia)........................... 5.1 kg (11.2 lb)
1. KENWOOD follows a policy of continuous advancements in development. For reason specifications may be changed without notice.
2. The full performance may not be exhibited in an extremely cold location (under a water-freezing temperature).
AM Tuner section (for Australia)
Tuning frequency range ......................... 531 kHz ~ 1,602 kHz
Usable sensitivity
(30% mod., S/N 20 dB) ..................... 20 µV / (700 µV / m)
Signal to noise ratio
(at 30% mod. 1mV input) .......................................... 48 dB

Kenwood C-V751 Specifications

General

harmonic distortion	0.01 %
signal to noise ratio	93 dB
sensitivity / impedance	200 mV / 47kΩ
controls S	± 10 dB (at 100 Hz)
BLE	± 10 dB (at 10 kHz)
level / impedance E REC	200 mV / 1 kΩ
composite	1 Vp-p/75 Ω
sampling frequency	32 kHz, 44.1 kHz, 48 kHz
input (coaxial)	0.5 Vp-p/75 Ω
optical	-15 dBm~-21 dBm, 600 nm ± 30 nm
frequency range	87.5 MHz~108 MHz
sensitivity (DIN) O	1.2 µV (at 75 Ω) / 13.2 dBf (40 kHz dev., S/N 26 dB)
sensitivity (DIN) REO	35 µV (at 75 Ω) / 42 dBf (46 kHz dev., S/N 46 dB)
signal to noise ratio (DIN weighted at 1 kHz, 40 kHz dev.) O	65 dB (65.2 dBf input)
signal to noise ratio (DIN weighted at 1 kHz, 40 kHz dev.) REO	60 dB (65.2 dBf input)
sensitivity (DIN ± 300 kHz)	64 dB
separation (DIN, 1 kHz)	36 dB
frequency response	30 Hz~15 kHz, + 0.5 dB, – 3.0 dB
tuning frequency range	531 kHz ~ 1, 602 kHz
usable sensitivity (30% mod., S/N 20 dB)	20 µV / (700 µV / m)
signal to noise ratio (at 30% mod. 1mV input)	48 dB
tuning frequency range	531 kHz ~ 1, 602 kHz
usable sensitivity (30% mod., S/N 20 dB)	20 µV / (700 µV / m)
signal to noise ratio (at 30% mod. 1mV input)	48 dB
tuning frequency range	153 kHz ~ 279 kHz
usable sensitivity (30% mod., S/N 20 dB)	35 µV
signal to noise ratio (at 30% mod. 1mV input)	45 dB
power consumption	35 W
dimensions (W x H x D)	400 mm x 105 mm x 382 mm
weight (net)	5.2 kg
weight (net) (For Australia)	5.1 kg