Kenwood C-V751 User Manual

54
Timer operation
Example: Adjustment to 8:15
CLOCK
÷ Press the CLOCK key. The hour is entered and the minute display
starts to blink.
÷ If you make a mistake, restart from the beginning.
÷ To adjust correct time, press the CLOCK key at the same moment as
a time announcement.
MULTI.CONTROL
LEVEL
MULTI.CONTROL
LEVEL
CLOCK
CLOCK
Clock adjustment
This unit incorporates a clock function. Be sure to adjust the
correct time before using the timer function.
The time display blinks after a power failure or when the power
cord has been unplugged from the AC outlet and plugged in
again. In such a case, adjust the clock again.
Activate the clock adjustment mode.
1 Press the CLOCK key.
Enter the hour.
3 Press the CLOCK key.
To decrease
the figure
To increase
the figure
Enter the minute.
2 Press the CLOCK key.
To decrease
the figure
To increase
the figure
Each press of DISPLAY
switches the displayed
information alternately.
Main unit
Main unit
GRC
Displaying the Time
KHz TIMER 1 2 TAPE2
/
AUTO SOUND
PRO LOGIC
DIGIT
A
3 S
T
MHz SLEEP
DOW
N
DIGIT
A
DTS DOLBY
DIGIT
A
AM 8: ))
KHz TIMER 1 2 TAPE
2
AUTO SOUND
PRO LOGIC
DIGIT
A
3
S
MHz SLEEP
DO
W
DIGIT
A
DTS DOLBY
DIGIT
A
AM 8: 1 5
1
3
2
2 Set the figure of hour.
1 Set the figure of minute.
To switch between the 12-hour/24-hour display
(Main unit only)
1 24-hour display
2 12-hour display
Clock adjustment
(Main unit only)
Press and hold the CLOCK key
1 Press and hold the CLOCK key for
more than 2 seconds. (The time dis-
play starts to blink.)
÷ From the second press, each press switches between 24h and 12h
alternately.
Main unit
Main unit
CLOCK

Kenwood C-V751 Specifications

General

harmonic distortion	0.01 %
signal to noise ratio	93 dB
sensitivity / impedance	200 mV / 47kΩ
controls S	± 10 dB (at 100 Hz)
BLE	± 10 dB (at 10 kHz)
level / impedance E REC	200 mV / 1 kΩ
composite	1 Vp-p/75 Ω
sampling frequency	32 kHz, 44.1 kHz, 48 kHz
input (coaxial)	0.5 Vp-p/75 Ω
optical	-15 dBm~-21 dBm, 600 nm ± 30 nm
frequency range	87.5 MHz~108 MHz
sensitivity (DIN) O	1.2 µV (at 75 Ω) / 13.2 dBf (40 kHz dev., S/N 26 dB)
sensitivity (DIN) REO	35 µV (at 75 Ω) / 42 dBf (46 kHz dev., S/N 46 dB)
signal to noise ratio (DIN weighted at 1 kHz, 40 kHz dev.) O	65 dB (65.2 dBf input)
signal to noise ratio (DIN weighted at 1 kHz, 40 kHz dev.) REO	60 dB (65.2 dBf input)
sensitivity (DIN ± 300 kHz)	64 dB
separation (DIN, 1 kHz)	36 dB
frequency response	30 Hz~15 kHz, + 0.5 dB, – 3.0 dB
tuning frequency range	531 kHz ~ 1, 602 kHz
usable sensitivity (30% mod., S/N 20 dB)	20 µV / (700 µV / m)
signal to noise ratio (at 30% mod. 1mV input)	48 dB
tuning frequency range	531 kHz ~ 1, 602 kHz
usable sensitivity (30% mod., S/N 20 dB)	20 µV / (700 µV / m)
signal to noise ratio (at 30% mod. 1mV input)	48 dB
tuning frequency range	153 kHz ~ 279 kHz
usable sensitivity (30% mod., S/N 20 dB)	35 µV
signal to noise ratio (at 30% mod. 1mV input)	45 dB
power consumption	35 W
dimensions (W x H x D)	400 mm x 105 mm x 382 mm
weight (net)	5.2 kg
weight (net) (For Australia)	5.1 kg