Kenwood C-V751 User Manual

13
Setup of the Graphical Remote Control (GRC) unit
Operation of Graphcal Remote Control
Perform the following procedure after inserting batteries for
the first time and every time after changing them.
Loading the batteries
Loading batteries
1 Remove the cover. 2 Insert batteries. 3 Close the cover.
Caution in battery replacement
÷ Insert 6 AA-size batteries as indicated by the
polarity marking.
÷ To maintain the memory of the settings you
made before, complete the battery replace-
ment operation within 30 seconds.
ª
·
Remote control operation
1 The touch screen responds to pressure
from the included stylus or your finger.
Calibrating the Touch screen
÷ When you touch each calibration point, you should hear a beep and see
the next point, indicating that area of the screen is now calibrated. If
you do not hear a beep, touch the calibration point until you do.
÷ The touch screen is sensitive to pressure, not to movement. Press
firmly but gently on any touch screen element. The screen will not
respond if you simply brush the stylus or your finger along the surface.
÷ If you are replacing batteries and complete the battery replacement
within 3 minutes, you do not need to calibrate the screen; calibration
is stored in memory.
1 To calibrate the touch screen, use the
stylus to touch the center of each of the
calibration points displayed.

Kenwood C-V751 Specifications

General

harmonic distortion	0.01 %
signal to noise ratio	93 dB
sensitivity / impedance	200 mV / 47kΩ
controls S	± 10 dB (at 100 Hz)
BLE	± 10 dB (at 10 kHz)
level / impedance E REC	200 mV / 1 kΩ
composite	1 Vp-p/75 Ω
sampling frequency	32 kHz, 44.1 kHz, 48 kHz
input (coaxial)	0.5 Vp-p/75 Ω
optical	-15 dBm~-21 dBm, 600 nm ± 30 nm
frequency range	87.5 MHz~108 MHz
sensitivity (DIN) O	1.2 µV (at 75 Ω) / 13.2 dBf (40 kHz dev., S/N 26 dB)
sensitivity (DIN) REO	35 µV (at 75 Ω) / 42 dBf (46 kHz dev., S/N 46 dB)
signal to noise ratio (DIN weighted at 1 kHz, 40 kHz dev.) O	65 dB (65.2 dBf input)
signal to noise ratio (DIN weighted at 1 kHz, 40 kHz dev.) REO	60 dB (65.2 dBf input)
sensitivity (DIN ± 300 kHz)	64 dB
separation (DIN, 1 kHz)	36 dB
frequency response	30 Hz~15 kHz, + 0.5 dB, – 3.0 dB
tuning frequency range	531 kHz ~ 1, 602 kHz
usable sensitivity (30% mod., S/N 20 dB)	20 µV / (700 µV / m)
signal to noise ratio (at 30% mod. 1mV input)	48 dB
tuning frequency range	531 kHz ~ 1, 602 kHz
usable sensitivity (30% mod., S/N 20 dB)	20 µV / (700 µV / m)
signal to noise ratio (at 30% mod. 1mV input)	48 dB
tuning frequency range	153 kHz ~ 279 kHz
usable sensitivity (30% mod., S/N 20 dB)	35 µV
signal to noise ratio (at 30% mod. 1mV input)	45 dB
power consumption	35 W
dimensions (W x H x D)	400 mm x 105 mm x 382 mm
weight (net)	5.2 kg
weight (net) (For Australia)	5.1 kg