Kenwood C-V751 User Manual

55
Timer operation
VOLUME CONTROL
DOWN
UP
TIMER
MODE
TIMER
SET
1 Select the program timer mode.
Timer operation
Two 24-hour timer systems (TIMER 1, TIMER 2) (which can
be used every day) and a sleep timer system (which works
only once) are available.
In each of TIMER 1 and TIMER 2, the timer data including the
operating period and played contents can be set and se-
lected to be activated or not as required.
Timer playback, timer recording (TIMER 1, TIMER 2)
With each of the two timer programs, a selected source can be
played (or radio broadcast can be recorded) in the previously set time
period.
Sleep timer
The unit is put to STANDBY mode automatically after the specified
period has elapsed.
I
Timer programming
Make preparations for the play (recording).
÷ To listen to radio ÷ To listen to CD ÷ To listen to MD ÷ For broadcast
recordings
÷ To listen to DVD
The station should be
preset before timer pro-
gramming.
‚qw
Insert a disc.
(Program playback is not pos-
sible.)
Insert a MD. Make prepara-
tions for record-
ing. °
Insert a disc.
(Program playback is not pos-
sible.)
Adjust the listening volume.
Select a TIMER No.
2 Press while reservation content is
displayed.
Each press of the key switches the TIMER numbers as follows.
1 TIMER 1
2 TIMER 2
3 TIMER 1,2
4 OFF
÷ The selected TIMER No. lights.
÷ If a previously programed TIMER No. is selected, the contents will be
replaced by the new contents programd.
÷ The timer programming operation is not possible when TIMER 1,2
have already been selected.
Main unit
Main unit
KHz TIMER 1 2 TAPE2/MONI.
AUTO SOUND
L
PRO LOGIC
DIGITAL REC
3 STEREO
C
R
LS
S
R
S
LFE SW
MHz SLEEP
DOWN MIX
DIGITAL CS
DTS DOLBY
DIGITAL REC
÷ The VOLUME CONTROL should be set to the desired volume while
the unit is ON.
Timer reservation is possible for the two types TIMER 1 and
TIMER 2 at the same time.
÷ Please make reservations with an interval of at least one minute, so
that the operation times of TIMER 1 and TIMER 2 do not overlap.
3
2
1
÷ The MUTE function is activated during timer recording.
TIMER
SET
MULTI.CONTROL
LEVEL
1 Set the figure of hour.
2 Enter the figure in memory.
Enter the ON time (Hour).
To decrease
the figure
To increase
the figure
÷ If you make a mistake, restart from step 3 .
Main unit
FM
LW
MW
AUTO SOUND
PRO LOGIC
DIGITAL R
3 STER
AM
MHz SLEEP
DOWN M
DIGITAL
DTS DOLBY
DIGITAL R
ON TIM
E
KHz TIMER 1 2 TAPE2/MO
FM
LW
MW
AUTO SOUND
PRO LOGIC
DIGITAL
R
3 STE
R
AM
MHz SLEEP
DOWN
M
DIGITAL
DTS DOLBY
DIGITAL
R
AM 1 ))
)
:
KHz TIMER 1 2 TAPE2/M
O
4

Kenwood C-V751 Specifications

General

harmonic distortion	0.01 %
signal to noise ratio	93 dB
sensitivity / impedance	200 mV / 47kΩ
controls S	± 10 dB (at 100 Hz)
BLE	± 10 dB (at 10 kHz)
level / impedance E REC	200 mV / 1 kΩ
composite	1 Vp-p/75 Ω
sampling frequency	32 kHz, 44.1 kHz, 48 kHz
input (coaxial)	0.5 Vp-p/75 Ω
optical	-15 dBm~-21 dBm, 600 nm ± 30 nm
frequency range	87.5 MHz~108 MHz
sensitivity (DIN) O	1.2 µV (at 75 Ω) / 13.2 dBf (40 kHz dev., S/N 26 dB)
sensitivity (DIN) REO	35 µV (at 75 Ω) / 42 dBf (46 kHz dev., S/N 46 dB)
signal to noise ratio (DIN weighted at 1 kHz, 40 kHz dev.) O	65 dB (65.2 dBf input)
signal to noise ratio (DIN weighted at 1 kHz, 40 kHz dev.) REO	60 dB (65.2 dBf input)
sensitivity (DIN ± 300 kHz)	64 dB
separation (DIN, 1 kHz)	36 dB
frequency response	30 Hz~15 kHz, + 0.5 dB, – 3.0 dB
tuning frequency range	531 kHz ~ 1, 602 kHz
usable sensitivity (30% mod., S/N 20 dB)	20 µV / (700 µV / m)
signal to noise ratio (at 30% mod. 1mV input)	48 dB
tuning frequency range	531 kHz ~ 1, 602 kHz
usable sensitivity (30% mod., S/N 20 dB)	20 µV / (700 µV / m)
signal to noise ratio (at 30% mod. 1mV input)	48 dB
tuning frequency range	153 kHz ~ 279 kHz
usable sensitivity (30% mod., S/N 20 dB)	35 µV
signal to noise ratio (at 30% mod. 1mV input)	45 dB
power consumption	35 W
dimensions (W x H x D)	400 mm x 105 mm x 382 mm
weight (net)	5.2 kg
weight (net) (For Australia)	5.1 kg