Nice WIDE L User Manual

2 – ENGLISH
ENGLISH
Translation of the original instructions in full
CONTENTS
GENERAL SAFETY WARNINGS AND
PRECAUTIONS
1
1 GENERAL SAFETY WARNINGS AND PRECAUTIONS
1.1 GENERAL WARNINGS
a
WARNING! Important safety instructions. Observe
all the instructions as improper installation may
cause serious damages.
a
WARNING! Important safety instructions. It is im-
portant to comply with these instructions to ensure
personal safety. Store these instructions carefully.
a
According to the latest European legislation, an au-
tomated device must be constructed in conformity
to the harmonised rules specied in the current
Machinery Directive, which allow for declaring the
presumed conformity of the automation. Conse-
quently, all the operations for connecting the prod-
uct to the mains electricity, its commissioning and
maintenance must be carried out exclusively by a
qualied and expert technician.
a
In order to avoid any danger from inadvertent re-
setting of the thermal cut-off device, this appliance
must not be powered through an external switching
device, such as a timer, or connected to a supply
that is regularly powered or switched off by the cir-
cuit.
WARNING! Please abide by the following warnings:
– Before commencing the installation, check the “Product
technical specications”, in particular whether this prod-
uct is suitable for automating your guided part. Should it
not be suitable, do NOT proceed with the installation.
– The product cannot be used before it has been commis-
sioned as specied in the “Testing and commissioning”
chapter.
– Before proceeding with the product’s installation, check
that all the materials are in good working order and suited
to the intended applications.
– The product is not intended for use by persons (including
children) with reduced physical, sensory or mental capac-
ities, nor by anyone lacking sufcient experience or famil-
iarity with the product.
– Children must not play with the appliance.
– Do not allow children to play with the product’s control
devices. Keep the remote controls out of reach of chil-
dren.
– The system’s power supply network must include a dis-
connection device (not supplied) with a contact opening
gap permitting complete disconnection under the condi-
tions envisaged by Overvoltage Category III.
– During the installation process, handle the product with
care by avoiding crushing, impacts, falls or contact with
liquids of any kind. Do not place the product near sources
of heat nor expose it to open ames. All these actions can
damage the product and cause it to malfunction, or lead
to dangerous situations. Should this occur, immediately
suspend the installation process and contact the Techni-
cal Assistance Service.
1 GENERAL SAFETY WARNINGS AND PRECAUTIONS . . . . . 2
1.1 General warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
1.2 Installation warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2 PRODUCT DESCRIPTION AND INTENDED USE . . . . . . . . . 3
2.1 List of constituent parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
3 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
3.1 Pre-installation checks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
3.2 Product usage limits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
3.2.1 Product durability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
3.3 Product identification and overall dimensions . . . . . . . . . . . . 5
3.4 RECEIPT OF THE PRODUCT . . . . . . . . . . . . . . . . . . . . . . . . 6
3.5 Pre-installation works . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3.6 Adjusting the boom gate . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
3.7 Installing the gearmotor . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
3.8 Installing the boom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
3.9 Adjusting the mechanical limit switches . . . . . . . . . . . . . . . . 12
3.10 Boom balancing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
3.11 Manually unlocking and locking the gearmotor . . . . . . . . . . 13
4 ELECTRICAL CONNECTIONS . . . . . . . . . . . . . . . . . . . . . . . 14
4.1 Preliminary checks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
4.2 Wiring diagram and description of connections . . . . . . . . . . 15
4.2.1 Wiring diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
4.2.2 Description of connections . . . . . . . . . . . . . . . . . . . . . . . 17
5 FINAL CHECKS AND START-UP. . . . . . . . . . . . . . . . . . . . . . 17
5.1 Power supply connection . . . . . . . . . . . . . . . . . . . . . . . . . . 17
6 FINAL CHECKS AND START-UP. . . . . . . . . . . . . . . . . . . . . . 18
5.2 Adjustment of the mechanical stop positions . . . . . . . . . . . 18
5.3 Checking the boom’s movement . . . . . . . . . . . . . . . . . . . . . 18
7 TESTING AND COMMISSIONING. . . . . . . . . . . . . . . . . . . . . 19
6.1 Testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
6.2 Commissioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
8 PROGRAMMING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
7.1 Adjusting the trimmers . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
7.2 ALT input and mechanical stop positions learning . . . . . . . . 22
7.3 Programming the control unit . . . . . . . . . . . . . . . . . . . . . . . 22
7.4 Memorising the transmitters . . . . . . . . . . . . . . . . . . . . . . . . 24
7.4.1 Procedure for memorising transmitter buttons . . . . . . . . 24
7.4.2 Number of transmitters that can be memorised . . . . . . . 24
7.4.3 Transmitter memorisation and deletion procedures . . . . . 25
7.5 LOCKING AND UNLOCKING THE MEMORY . . . . . . . . . . . 26
7.6 Special functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
7.6.1 “Move anyway” function . . . . . . . . . . . . . . . . . . . . . . . . . 26
7.6.2 “Maintenance notice” function . . . . . . . . . . . . . . . . . . . . 26
7.6.3 Verifying the number of manoeuvres completed . . . . . . . 26
7.6.4 Manoeuvre counter resetting . . . . . . . . . . . . . . . . . . . . . 26
9 TROUBLESHOOTING GUIDE . . . . . . . . . . . . . . . . . . . . . . . . 27
8.1 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
8.2 Signals on the control unit . . . . . . . . . . . . . . . . . . . . . . . . . . 28
10 FURTHER DETAILS (Accessories) . . . . . . . . . . . . . . . . . . . . 29
9.1 Connecting an SM-type radio receiver . . . . . . . . . . . . . . . . 29
9.2 Connecting and installing the back-up battery . . . . . . . . . . . 29
9.3 Connecting the Oview programmer . . . . . . . . . . . . . . . . . . . 30
9.4 Connecting the boom lights (optional accessory) . . . . . . . . 31
9.4.1 Photocells . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
11 PRODUCT MAINTENANCE. . . . . . . . . . . . . . . . . . . . . . . . . . 33
12 PRODUCT DISPOSAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
13 TECHNICAL SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . 34
14 CONFORMITY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
INSTRUCTIONS AND WARNINGS FOR THE USER. . . . . . 37
MAINTENANCE SCHEDULE (to be handed to the end
user). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Nice WIDE L Specifications

General

Brand	Nice
Model	WIDE L
Category	Control Systems
Language	English