Roland E-A7 Reference Manual

11
The following parameters can be set for each Performance memory:
Parameter/Group Explanation
Keyboard Part Mixer
Here you can make settings for the keyboard parts
(UP1, UP2, UP3, LWR).
Keyboard Part MFX
Here you can make eect settings for the keyboard
parts (UP1, UP2, UP3, LWR).
Style Part Mixer Here you can make settings for the style parts.
Arranger Setting
This function group allows you to specify where and
how the selected Style should scan the note messages
generated by your playing for chord information.
Melody Intelligent
Here you can make settings for the Melody Intelligent
function.
Melody Intelligent is a function that automatically
adds harmony to the keyboard parts.
Split Here you can specify the split point of the keyboard.
Scale Tune Switch
Here you can specify the parts for which the Scale
Tune setting is enabled.
Scale Tune
Here you can specify how the pitch will be adjusted
in units of one cent (1/100 of a semitone) relative to
equal temperament.
Pad Setting Here you can make settings for the pads.
Assignable Setting
Here you can make settings for the assignable switch-
es and control pedal.
Keyboard Part Mixer Parameters
This function group can be selected using [MENU]
0
“User
Program Edit”
0
“Keyboard Part Mixer.” You can also access the
Keyboard Part Mixer screen by pressing the [F1] button (Kbd Mixer)
of the left main screen.
The vertical columns correspond to each keyboard part (UP1, UP2,
UP3, LWR).
The horizontal rows show parameters that you can edit.
Use the direct buttons and Cursor buttons to select the desired
parameter, and use the Value [-] [+] buttons or the Balance/Value
knob (when the LED is unlit) to edit the value.
The following parameters are available:
Reverb Send
Signal level sent from each part to reverb
Parameter Value
Reverb Send 0–127
Chorus Send
Signal level sent from each part to chorus
Parameter Value
Chorus Send 0–127
Pan
Pan (left/right position) of each part
Parameter Value
Pan L64–0–R63
Volume/Part Switch
Volume and on/o setting of each part
Parameter Value
Volume 0–127
MFX Switch
The E-A7 provides one multi-eect (MFX) for the keyboard parts.
For each part, you can specify whether the MFX is applied.
Parameter Value
MFX Switch O, On
Key Touch (velocity sensitivity)
Here you can make settings for the keyboard touch.
Parameter Value Explanation
Key Touch Curve
High, Medium,
Low, Fixed*
High: Select this setting for max-
imum expressiveness. Even small
variations of the force with which
you strike a key produce audible
changes. The trade-o is, however,
that you have to strike the keys
forcefully to reach the maximum
volume.
Medium: Medium velocity sensitivi-
ty.
The keyboard responds to velocity
changes, but the maximum volume
can be obtained more easily than
with “High.” (This is the default
setting.)
Low: Select this setting if you are
used to playing on an electronic
organ or if you do not want velocity
changes to bring about major vol-
ume changes.
Fixed: Select this setting if all notes
you play on the keyboard should
have the same velocity value. When
you set this parameter, the “Key
Touch Fixed” eld can be edited
Key Touch Min 1–126
This parameter allows you to set the
smallest velocity value with which
you can trigger the selected part.
Key Touch Max 2–127
This parameter allows you to set the
highest velocity value with which
you can trigger the selected part.
Key Touch Fixed* 1–127
Allows you to set the value when
“Curve” is set to “Fixed.”
[*] This parameter can only be edited if the “Key Touch Curve”
parameter is set to “Fixed.”
EQ
Here you can make equalizer (EQ) settings for each keyboard part.
Parameter Value Explanation
EQ Switch O, On
This parameter allows you to switch
the equalizer on and o.
High Freq (Hz)
1500, 2000,
3000, 4000,
6000, 8000,
12000
Allows you to set the cuto frequen-
cy of the high band (this is a shelving
lter).
High Gain (dB) -15–+15
Use this parameter to set the level of
the selected “High” frequency.
Positive values boost (increase the
volume of) that frequency band,
negative values cut (attenuate) it.
Mid Freq (Hz)
200, 250, 315,
400, 500, 630,
800, 1000,
1250, 1600,
2000, 2500,
3150, 4000,
5000, 6300,
8000
Allows you to set the cuto fre-
quency of the middle band (this is a
peaking lter).
Mid Gain (dB) -15–+15
Use this parameter to set the level of
the selected “Mid” frequency.
User Program Edit Parameters

Roland E-A7 Specifications

General

Equalizer	Yes
Product type	Digital synthesizer
Product color	Black
Sound effects	Chorus, Equalization, Reverberation
RMS rated power	24 W
Number of speakers	2
Keyboard number of keys	61
Maximum polyphony (notes)	128
Power source type	DC
Display type	LCD

Weight and Dimensions

Depth	318 mm
Width	1045 mm
Height	136 mm
Weight	7900 g