TOHATSU MX 50D2 User Manual

TOOL KIT AND SPARE PARTS 55
11
The following a list of the tools and spare parts provided with the motor.
* Not included as standard accessories in some markets.
Name Quantity Remark
Servicing Tools
Tool B a g
Socket Wrench (21mm)
Socket Wrench (10 x 13)
Socket Wrench Handle
Pliers
Screwdriver (Phillips-type and flat head)
1
1
1
1
1
1Adapter-type
Spare Parts
Cylinder Head Cover Gasket
Cylinder Head Gasket
Engine Basement Gasket
Float Valve
Throttle Wire
Anode (for Bracket)
Trim Tab
Water Pump Impeller
Guide Plate Gasket
Pump Case Gasket
Gasket (for Gear Oil Plug)
Grease
Starter Rope
Spark Plug
Split Pin
Rigging Bolt Set
1
1
1
3
2
1
1
1
1
1
2
1
1
3
1
4
4
4
4
NGK B8HS-10
12mm
12mm
Parts Packaged with Engine*
Fuel Tank (with primer bulb)
Grease Up Point Chart
Owner's Manual
Caution Label Information Card
1
1
1
1
Bolt
Nut
Washer A (large)
Washer B (small)
TOOL KIT AND SPARE PARTS
MWX50D2_E.book Page 55 Thursday, August 18, 2011 5:29 PM

TOHATSU MX 50D2 Specifications

General

Engine Type	2-Stroke
Starting	Manual
Gear Ratio	2.08:1
Fuel Type	Gasoline
Oil Type	2-stroke engine oil
Shaft Length	15 inches

Summary

General Safety Information

Safety Warnings and Symbols

Explains DANGER, WARNING, CAUTION, and Note indicators for critical information.

Emergency Stop Switch and Safe Operation

Details the emergency stop switch function and general safe boat operation practices.

Servicing, Maintenance, and Mounting

Outlines recommendations for authorized service, owner maintenance duties, and proper motor mounting.

Specifications

Names of Parts

Installation

Mounting the Outboard Motor on Boat

Instructions for positioning and securing the outboard motor to the boat transom.

Propeller Selection Guide

Guidance on choosing a propeller for optimal engine performance at wide open throttle.

Pre-Operating Preparations

Recommended Gasoline Types

Specifies the type of unleaded gasoline required for optimal engine performance and longevity.

Recommended Engine Oil

Details the type of two-stroke engine oil and fuel-to-oil mixing ratios for operation and break-in.

Break-in Procedure

Outlines the necessary steps for breaking in a new outboard motor for proper component seating and longevity.

Engine Operation

Starting and Warming Up

Procedures for safely starting the engine and warming it up to operating temperature.

Operating Modes and Conditions

Covers forward/reverse engagement, shallow water running, and mooring procedures.

Engine Stopping and Trim Adjustment

Proper engine stopping methods and how to adjust the trim angle for optimal boat handling.

Removing and Carrying the Outboard Motor

Removing the Outboard Motor

Steps required to safely detach the outboard motor from the boat for transport or storage.

Carrying and Storing the Outboard Motor

Guidelines for safely transporting and storing the outboard motor, including preparation steps.

Trailering

Adjustment

Trim Tab Adjustment

How to adjust the trim tab to balance steering loads for straight running.

Steering Load Adjustment

Adjusting the steering resistance for comfortable and safe operation.

Throttle Grip Turning Load Adjustment

Adjusting the friction on the throttle grip for smooth control and preventing accidental movement.

Inspection and Maintenance

Daily Inspection and Checks

Daily checks to perform before and after using the outboard motor for safety and performance.

Basic Maintenance Procedures

Covers washing the motor, and replacing propellers and spark plugs.

Scheduled and Seasonal Maintenance

Outlines periodic servicing, anode inspection, gear oil change, cleaning, storage, and pre-season checks.

Incident Response and Precautions

Procedures for checks after impact, engine submersion, and precautions for cold weather operation.

Troubleshooting

Tool Kit and Spare Parts

Optional Accessories

Propeller Table

Wiring Diagram