3.2 Operating Procedures for Utility Functions
3.2.36 JOG Speed Table Edit/Save (FnB05)
3-118
3.2.36
JOG Speed Table Edit/Save (FnB05)
This function edits and saves JOG speed tables. Saving a JOG speed
table to flash memory after editing it ensures that the data will be
retained even after the control power has been turned off.
Refer to the following manual for information on interpreting the dis-
plays.
Σ-7-Series Σ-7S SERVOPACK Command Option Attachable Type with INDEXER
Module Product Manual (Manual No.: SIEP S800001 64)
Preparation
Always check the following before you edit or save a jog speed table.
• The parameters must not be write-prohibited (Fn010 must be set to
0000).
• A JOG speed table save operation must not be in progress for any
means other than the digital operator.
Editing JOG Speed Tables
The operating procedure when setting the value for JOG speed
table number 5 is explained here.
Step Operation Result
1
Press the key to open the Util-
ity Function Mode main menu, and
move the cursor with the
keys to select FnB05.
2
Press the key to view the
FnB05 operation screen.
3
Move the cursor using the
keys to select the JOG speed table
number to be edited.
Pressing the key when the cur-
sor is on JOG speed table number 0
moves it to number 15.
Pressing the key when the cur-
sor is on JOG speed table number
15 moves it to number 0.
Continued on next page.
㹀㹀ࠉࠉࠉࠉࠉ㹄㹓㹌㹁㹒㹇㹍㹌
㹄㹬㹀㸮㸲ࠉ㹘㹍㹌㹃ࠉ㹃㹢㹧㹲
㹄㹬㹀㸮㸳ࠉ㹈㹑㹎㹂ࠉ㹃㹢㹧㹲
㹄㹬㹀㸮㸴ࠉ㹎㹅㹋ࠉ㹇㹬㹧㹲
㹄㹬㹀㸮㸵ࠉ㹘㹍㹌㹃ࠉ㹇㹬㹧㹲
㹀㹀ࠉࠉࠉࠉࠉ㹈㹱㹮㹢㹃㹢㹧㹲
㹈㹑㹎㹂㸮㸮㸮㸻㸮㸮㸮㸮㸯㸮㸮㸮
㹈㹑㹎㹂㸮㸮㸯㸻㸮㸮㸮㸮㸯㸮㸮㸮
㹈㹑㹎㹂㸮㸮㸰㸻㸮㸮㸮㸮㸯㸮㸮㸮
㹈㹑㹎㹂㸮㸮㸱㸻㸮㸮㸮㸮㸯㸮㸮㸮
㹀㹀ࠉࠉࠉࠉࠉ㹈㹱㹮㹢㹃㹢㹧㹲
㹈㹑㹎㹂㸮㸮㸰㸻㸮㸮㸮㸮㸯㸮㸮㸮
㹈㹑㹎㹂㸮㸮㸱㸻㸮㸮㸮㸮㸯㸮㸮㸮
㹈㹑㹎㹂㸮㸮㸲㸻㸮㸮㸮㸮㸯㸮㸮㸮
㹈㹑㹎㹂㸮㸮㸳㸻㸮㸮㸮㸮㸯㸮㸮㸮