Home
Atlas Copco
Drill
SmartROC T45--10
Atlas Copco SmartROC T45--10 User Manual
5
of 1
of 1 rating
88 pages
Give review
Manual
Specs
To Next Page
To Next Page
To Previous Page
To Previous Page
Loading...
1
3
Table of Contents
Table of Contents
3
Introduction
5
Safety First
5
The Purpose of this Publication
5
Target Group
5
Product Description
7
Intended Use of the Product
7
Nonintended Use of the Product
7
Main Components
8
Data Plate
9
Controls and Instruments
11
Operating Controls
12
Right Control Panel
13
Left Lever in Tram Mode/Positioning Mode
14
Left Lever in Drill Mode
15
Right Lever in Tram Mode/Positioning Mode
16
Right Lever in Drill Mode
17
Tramming Levers
19
Operator's Environment Control Panel
20
Winch Control Unit
22
Operation
25
Startup and Shutdown
25
Turning on Battery Power
25
Turning off Battery Power
25
Starting the Diesel Engine
26
Warming up the System
27
Particle Filter Regeneration
28
Delayed Engine Shutdown
29
Stopping the Diesel Engine
30
Activating the Winch Control Unit
31
Deactivating the Winch Control Unit
31
Tramming
32
Preparations before Tramming
32
Basic Tramming
33
Tramming on Level Ground
34
Tramming Uphill
34
Tramming Downhill
35
Tramming on Sideway Slopes
35
Checking before Using the Winch
36
Using the Winch When Tramming
36
Checking after Tramming
37
Positioning
38
System Settings
38
Machine Positioning
40
Drill System Positioning
42
Rod Handling
44
Loading the Rod Carousel
44
Drilling
47
Drilling Settings
47
Drill a Hole
48
Stop Drilling
49
Adding Drill Rods
49
Changing a Drill Bit
51
Checks During Drilling
51
In Case of Breakdown or Incident
52
Transport
55
Preparations before Hoisting
55
Before Loading the Machine Onto the Transport Vehicle
55
Hoisting a Drill Rig
56
Before Transporting the Loaded Drill Rig
57
Daily Maintenance
59
Maintenance Table
59
Daily Maintenance Procedures
59
Visual Check
59
Wash Machine Externally
61
Check Lubrication Oil Level Tank
61
Drain Condensate in Pressure Tank
61
Check Fire Extinguishers
62
Check Emergency Stops and Work Lights
63
Check Coolant Level
64
Check Track Frames
65
Check Motor Oil Level
66
Check Diesel Engine and Compressor
67
Check Hydraulic Tank
68
Drain Prefilter
68
Check Compressor Oil Level
69
Check Condition of CLS Pump
69
Check Winch
70
Check Small Remote Control
70
Technical Data
73
Dimensions
75
Highest Permitted Inclination Angles for Tramming and Drill Rig Setup
78
Ordinary Tramming
79
Tramming with the Feed in Vertical Position and Centered between the Track Frames
80
Drill Rig Setup: the Feed in Vertical Position and Centered between the Track Frames
81
Drill Rig Setup: the Feed in Vertical Position and the Boom Swung Maximum to the Left
82
Drill Rig Setup: the Feed in Vertical Position and the Boom Swung Maximum to the Right
83
Drill Rig Setup: the Feed Top in Extreme Position Forward, the Feed Laterally Vertical and Centered between the Track Frames
84
Drill Rig Setup: the Feed Top in Extreme Position Forward and to the Left, and with the Boom Swung Maximum to the Left
85
Drill Rig Setup: the Feed Top in Extreme Position Forward and to the Right, and with the Boom Swung Maximum to the Right
86
5
Based on 1 rating
Ask a question
Give review
Questions and Answers:
Need help?
Do you have a question about the Atlas Copco SmartROC T45--10 and is the answer not in the manual?
Ask a question
Atlas Copco SmartROC T45--10 Specifications
General
Brand
Atlas Copco
Model
SmartROC T45--10
Category
Drill
Language
English
Related product manuals
Atlas Copco SRD 20
24 pages
Atlas Copco PHE 6 S
18 pages
Atlas Copco Secoroc YT29A
20 pages
Atlas Copco PHE 3X
14 pages
Atlas Copco BBC 16W
196 pages
Atlas Copco Pionjar
28 pages
Atlas Copco Cobra 148
47 pages
Atlas Copco Cobra 248
47 pages
Atlas Copco Pionjar 130
76 pages
Atlas Copco PHE 16 RL-N
6 pages
Atlas Copco Pionjar 120
76 pages
Atlas Copco PowerROC T30 E
91 pages
Need help?
General
To Next Page