To Next Page

To Previous Page

11-10 G60 Generator Protection System GE Multilin

11.6 DISPOSAL 11 MAINTENANCE

11.6DISPOSAL 11.6.1 DISPOSAL

Other than the battery, there are no special requirements for disposal of the unit at the end its service life. For customers

located in the European Union, dispose of the battery as outlined earlier. To prevent non-intended use of the unit, remove

the modules as outlined earlier, dismantle the unit, and recycle the metal when possible.

Default Chapter3
- Table of Contents3
1 Getting Started11
- Important Procedures11
  - Cautions and Warnings11
  - Inspection Procedure12
- Ur Overview13
- Enervista Ur Setup Software16
- Ur Hardware28
- Using the Relay29
2 Product Description33
- Introduction33
- Specifications47
3 Hardware63
- Description63
- Wiring71
- Direct Input and Output Communications Modules91
- Field and Stator Ground Modules109
4 Human Interfaces131
- Enervista Ur Setup Software Interface131
- Extended Enervista Ur Setup Features134
- Faceplate Interface143
5 Settings157
- Overview161
- Product Setup168
- System Setup253
- Flexlogic296
- Grouped Elements319
- Control Elements415
- Inputs/Outputs452
- Transducer Inputs and Outputs470
- Testing481
6 Actual Values487
- Overview487
  - Actual Values Menu487
- Status487
- Records514
- Product Information516
  - Model Information516
  - Firmware Revisions516
7 Commands and519
- Commands519
8 Theory of Operation533
- Phase Distance through Power Transformers533
  - Description533
  - Example536
9 Application of Settings539
- Setting Example539
- Phase Distance through Power Transformers552
  - Overview552
  - Example553
10 Commissioning555
- Testing555
  - Testing Underfrequency and Overfrequency Elements555
11 Maintenance557
- Modules557
  - Replace a Module557
- Batteries559
  - Replace Battery559
  - Dispose of Battery560
- Uninstall and Clear Files and Data563
- Repairs564
- Storage565
- Disposal566
Parameter Lists567
- Flexanalog Items567
- A.1.1 Flexanalog Items567
- Flexinteger Items594
- A.1.2 Flexinteger Items594
Modbus Communications595
Modbus Rtu Protocol595
- Introduction595
- Physical Layer595
- Data Link Layer595
- B.1.1 Introduction595
- Modbus Rtu Crc-16 Algorithm596
Modbus Function Codes598
- Supported Function Codes598
- Read Actual Values or Settings (Function Code 03/04H598
- Execute Operation (Function Code 05H599
- Store Single Setting (Function Code 06H599
- Store Multiple Settings (Function Code 10H600
- Exception Responses600
File Transfers601
- Obtaining Relay Files Via Modbus601
Memory Mapping603
- Modbus Memory Map603
- Data Formats671
- B.4.2 Data Formats671
Iec 61850709
Overview709
- Introduction709
- Communication Profiles709
- C.1.1 Introduction709
- File Transfer by Iec 61850710
Server Data Organization711
- Overview711
- Ggio1: Digital Status Values711
- Ggio2: Digital Control Values711
- Ggio3: Digital Status and Analog Values from Goose Data711
- Ggio4: Generic Analog Measured Values711
- C.2.1 Overview711
- Mmxu: Analog Measured Values712
- Protection and Other Logical Nodes712
Server Features and Configuration714
- Buffered/Unbuffered Reporting714
- File Transfer714
- Timestamps and Scanning714
- Logical Device Name714
- Location714
- Logical Node Name Prefixes715
- Connection Timing715
- Non-Iec 61850 Data715
- Communication Software Utilities715
Generic Substation Event Services: Gsse and Goose716
- Overview716
- Gsse Configuration716
- Fixed Goose716
- Configurable Goose716
- C.4.1 Overview716
- Ethernet Mac Address for Gsse/Goose719
- Gsse ID and Goose ID Settings719
Iec 61850 Implementation Via Enervista Ur Setup720
- Overview720
- C.5.1 Overview720
- Configuring Iec 61850 Settings721
- About ICD Files722
- Creating an ICD File with Enervista Ur Setup726
- About Scd Files726
- Importing an Scd File with Enervista Ur Setup729
Acsi Conformance731
- Acsi Basic Conformance Statement731
- Acsi Models Conformance Statement731
- Acsi Services Conformance Statement732
Logical Nodes732
- Logical Nodes Table735
- Interoperability Document739
- D.1.1 Interoperability Document739
- Iec 60870-5-104 Point List747
Device Profile Document749
- Dnp V3.00 Device Profile749
- E.1.2 Implementation Table752
Dnp Point Lists756
- Binary Input Points756
- Binary and Control Relay Output757
- Counters758
- E.2.3 Counters758
- Analog Inputs759
- E.2.4 Analog Inputs759
- Radius Server Configuration761
Change Notes763
- Revision History763
- G.1.1 Revision History763
- Changes to the G60 Manual764
Abbreviations768
- Standard Abbreviations768
- G.2.1 Standard Abbreviations768
Warranty770
- Ge Multilin Warranty770
- G.3.1 Ge Multilin Warranty770

Brand	GE
Model	G60
Category	Protection Device
Language	English

GE G60 User Manual

Table of Contents

Questions and Answers:

GE G60 Specifications

Related product manuals