KEB COMBIVERT R6-N User Manual

Introduction
© KEB, 2015-07 COMBIVERT R6-N Page1.1 - 7
1
10
3.5 Regenerative adjustments ........................................................................... 3.5 - 3
3.5.1 Operating mode .............................................................................................. 3.5 - 3
3.5.2 Activate regeneration ...................................................................................... 3.5 - 3
3.5.3 Deactivate regeneration .................................................................................. 3.5 - 4
3.5.4 Optimization for regeneration .......................................................................... 3.5 - 4
3.6 Protection functions ..................................................................................... 3.6 - 3
3.6.1 Error and warning messages .......................................................................... 3.6 - 3
3.6.1.1 Undervoltage ........................................................................................................ 3.6 - 4
3.6.1.2 Overvoltage .......................................................................................................... 3.6 - 4
3.6.1.3 Overcurrent........................................................................................................... 3.6 - 4
3.6.1.4 Overload ............................................................................................................... 3.6 - 5
3.6.1.5 Inverter over temperature ..................................................................................... 3.6 - 5
3.6.1.6 External fault......................................................................................................... 3.6 - 5
3.6.1.7 Bus error ............................................................................................................... 3.6 - 5
3.6.1.8 Set selection error ................................................................................................ 3.6 - 6
3.6.1.9 Hardware error ..................................................................................................... 3.6 - 6
3.6.1.10 Regeneration error ............................................................................................... 3.6 - 6
3.6.2 Response to malfunction messages ............................................................... 3.6 - 7
3.6.2.1 Selection of the response ..................................................................................... 3.6 - 7
3.6.2.2 General fault reset (Pn.15) ................................................................................... 3.6 - 8
3.6.3 Automatic Restart ........................................................................................... 3.6 - 8
3.6.3.1 Undervoltage error (E.UP) .................................................................................... 3.6 - 9
3.6.3.2 Overvoltage error (E.OP)...................................................................................... 3.6 - 9
3.6.3.3 Overcurrent error (E.OC) ...................................................................................... 3.6 - 9
3.6.3.4 Malfunction messages and pre-warnings ............................................................. 3.6 - 9
3.6.4 Special functions ............................................................................................. 3.6 - 9
3.7 Parameter sets .............................................................................................. 3.7 - 3
3.7.1 Not set-programmable parameters ................................................................. 3.7 - 3
3.7.2 Security-Parameters ....................................................................................... 3.7 - 3
3.7.3 Indirect and direct set-addressing ................................................................... 3.7 - 3
3.7.4 Copying of parameter sets via keyboard (Fr.01) ............................................. 3.7 - 4
3.7.5 Copying of parameter sets via bus (Fr.01, Fr.09) ............................................3.7 - 5
3.7.6 Parameter set selection .................................................................................. 3.7 - 6
3.7.7 Locking of parameter sets ............................................................................... 3.7 - 9
3.7.8 Parameter set ON/OFF delay (Fr.05, Fr.06) ...................................................3.7 - 9
3.8 Special Functions ......................................................................................... 3.8 - 3
3.8.1 Timer and Counter .......................................................................................... 3.8 - 3
3.8.2 Mask out inverter state (Pn.30) ....................................................................... 3.8 - 6
3.8.3 Master / Slave input selection ......................................................................... 3.8 - 6

KEB COMBIVERT R6-N Specifications

General

Brand	KEB
Model	COMBIVERT R6-N
Category	Inverter
Language	English