English – 3
GENERAL WARNINGS: SAFETY - INSTALLATION - USE (instructions translated from Italian)
WARNING Important safety instructions. Observe all the instructions as improper installation may cause serious damage
WARNING Important safety instructions. It is important to comply with these instructions to ensure personal safety. Store
these instructions
• Before commencing the installation, check the “Product technical specications”, in particular whether this product is suitable for automating
your guided part. Should it be unsuitable, DO NOT proceed with the installation
• The product cannot be used before it has been commissioned as specied in the “Testing and commissioning” chapter
WARNING According to the most recent European legislation, the implementation of an automation system must comply with
the harmonised standards set forth in the Machinery Directive in force, which allow for declaring the presumed
conformity of the automation. On account of this, all operations regarding connection to the mains electricity, as
well as product testing, commissioning and maintenance, must be performed exclusively by a qualied and skilled
technician!
• Before proceeding with the product’s installation, check that all materials are in good working order and are suitable for the intended applications
• The product is not intended for use by persons (including children) with reduced physical, sensory or mental capacities, nor by anyone lacking
sufcient experience or familiarity with the product
• Children must not play with the appliance
• Do not allow children to play with the control devices of the product. Keep the remote controls out of reach of children
WARNING In order to avoid any danger from inadvertent resetting of the thermal cut-off device, this appliance must not be powered
through an external switching device, such as a timer, or connected to a supply that is regularly powered or switched off by
the circuit
• Provide a disconnection device (not supplied) in the plant’s mains power supply, with a contact opening distance that ensures complete
disconnection under the conditions envisaged by Overvoltage Category III
• During the installation, handle the product with care by preventing crushing, impacts, falls and contact with uids of any type; do not install the
product close to sources of heat, nor expose it to open ames. Failure to observe the above can damage the product and increase the risk
of danger or malfunctions. If this should happen, stop installation immediately and contact the Customer Service
• The manufacturer assumes no liability for damage to property, items or persons resulting from non-compliance with the assembly instructions.
In such cases the warranty does not cover material defects
• The weighted sound pressure level of the emission A is lower than 70 dB(A)
• Cleaning and maintenance to be carried out by the user must not be carried out by unsupervised children
• Before intervening on the system (maintenance, cleaning), always disconnect the product from the mains power supply and any back-up
batteries
• Check the system periodically, in particular all cables, springs and supports to detect possible imbalances, signs of wear or damage. Do not
use the product if repairs or adjustments are necessary, since an installation failure or an incorrectly balanced door may cause injury
• The packaging materials of the product must be disposed of in compliance with local regulations
• The product must not be installed outdoors
• Keep an eye on moving doors and do not let anyone go near them until they have opened or closed fully
• Be careful when activating the manual release (manual manoeuvre) device, as an open door may fall suddenly due to weak or broken springs,
or if it is unbalanced
• Every month, check that the drive motor reverses when the door encounters a 50 mm-high object placed on the ground. If necessary, readjust
the door and check it again, as incorrect adjustment is potentially dangerous (for drive motors incorporating a trapping safety system that
intervenes when the door's lower edge encounters an obstacle)
• If the power cable is damaged, it must be replaced by the manufacturer or by an appointed servicing company or similarly qualied person
in order to prevent any form of risk.
• Transport the product using the relevant hand trolley and the handles on the package to ensure that the operations are conducted safely.
INSTALLATION PRECAUTIONS
• Prior to installing the drive motor, check that the door is in good working order, correctly balanced and that it opens and closes properly
• Prior to installing the motor, remove all unnecessary cables or chains and deactivate any equipment – such as locking devices – not necessary
for motor-driven operation
• Check that there are no points where trapping or crushing against xed parts can occur when the moving section is in the fully open or closed
position; adequately protect any such parts
• Install the manoeuvring assembly for manual release (manual manoeuvre) at a height below 1.8 m
NOTE: if removable, the manoeuvring assembly must be kept close to the door
• Make sure that the controls are kept at a safe distance from moving parts, while allowing a good view of these.
The manoeuvring assembly of a switch kept manually closed must be located in a position that is visible from the guided part but far from
moving parts. It must be installed at a minimum height of 1.5 m
• Permanently attach the trapping hazard warning labels in a highly visible location or near the xed control devices (if present)
• Permanently attach the manual release (manual manoeuvre) label close to the manoeuvring assembly
• After installation, make sure that the motor prevents or stops door opening when the latter is loaded with a 20-kg weight secured to the centre
of its bottom edge (for drive motors that can be used with doors having opening widths exceeding 50 mm)
• After installation, make sure that the mechanism is properly adjusted and that the motor reverses when the door collides with a 50 mm-tall
object placed on the ground (for drive motors incorporating a trapping safety system that intervenes when the bottom edge of the door
encounters an obstacle);
Following installation, check and ensure that no door parts obstruct public roadways or pavements.
To Next Page
Loading...
Need help?
General
