Raymarine ST70+ User Manual

Chapter 1: General information 11
1.5 System information
ST70+ displays and keypads connect to Raymarine SeaTalk
ng
systems. Further
information on SeaTalk
ng
is given in the SeaTalk
ng
Reference Manual.
When connected to a SeaTalk
ng
system, the ST70+ displays repeat the data on the
bus. You can set the display response as required. You can set the system variation
only if it has not been set at another product.
You can also calibrate the system transducers and set the data units you want to apply
to the system.
Power protocol
Power to ST70+ is switched on and off using the power button (as described in
the ST70+ Operating Guide). However, where instruments are part of a system, it
may be more convenient to switch power for the entire system from a central circuit
breaker.
In this case, when system power is switched ON again:
• ST70+ instruments that were switched on when power was last switched off will
return to the switched ON state.
• ST70+ instruments that were OFF when system power was last switched OFF will
remain OFF and will need to be switched ON individually using their power but-
tons.
85024_1.book Page 11 Tuesday, January 27, 2009 11:31 AM

Raymarine ST70+ Specifications

General

Display Type	LCD
Waterproof	Yes
Waterproof Rating	IPX6
Interface	NMEA 2000
Power Supply	12V DC
Backlighting	Yes
Network	NMEA 2000
Input Voltage	10-32V DC
Dimensions	110mm

Summary

Preface

Preface Safety Notices

Important warnings about product installation, operation, and safe navigation.

Preface EMC Conformance

Information on electromagnetic compatibility standards for marine environments.

Preface Pressure Washing

Warning against using pressure washers on Raymarine products.

Preface Certified Installation

Recommendation for certified installation for enhanced warranty benefits.

Preface Product Documents

Lists available user documents for the ST70+ system.

Preface Technical Accuracy

Disclaimer regarding the accuracy and potential changes in specifications.

Preface Product Disposal

Guidance on proper disposal of electronic equipment according to WEEE directive.

Chapter 1: General Information

Chapter 1: 1.1 Introduction

Overview of the manual's content for commissioning and setup information.

Chapter 1: 1.2 Product Basics

Describes the ST70+ system components and their basic functions.

Chapter 1: 1.3 Setup Principles

Explains the mandatory commissioning and initial setup procedures before operation.

Chapter 1: 1.4 Normal Operation

Details day-to-day operation of Pilot Controllers and Instruments.

Chapter 1: 1.5 System Information

Information on connecting ST70+ to Raymarine SeaTalkng systems.

Chapter 1: 1.6 Commissioning Requirement

Outlines the mandatory commissioning procedures before using ST70+ products.

Chapter 2: Commissioning Procedures

Chapter 2: 2.1 Requirement

Stresses the need for commissioning procedures before operational use.

Chapter 2: 2.2 Initial Setup

Details the sequence of initial setup steps for the ST70+ system.

Chapter 2: 2.3 Dockside Setup

Covers dockside setup procedures like autopilot system and transducer configuration.

Chapter 2: 2.4 Open Water Calibration

Guides through open water calibration for autopilot and instrument systems.

Chapter 2: 2.5 Checking Autopilot Operation

Procedures to verify the correct functioning of the autopilot after calibration.

Chapter 3: Setup Information

Chapter 3: 3.1 Introduction

Explains setup functions for optimizing ST70+ performance.

Chapter 3: 3.2 General Setup

Covers changing system parameters like language, vessel type, and time/date.

Chapter 3: 3.3 Autopilot Setup

Details how to adjust autopilot drive settings for optimal performance.

Chapter 3: 3.4 System Configuration

Explains how to configure display functions and group keypads.

Chapter 4: Maintenance & Troubleshooting

Chapter 4: 4.1 Introduction

Provides information for identifying problems and maintaining the ST70+ system.

Chapter 4: 4.2 Maintenance

Outlines basic user maintenance tasks for ST70+ displays and keypads.

Chapter 4: 4.3 Troubleshooting

Offers guidance on identifying and resolving common issues with the ST70+ system.

Chapter 4: Display Self-Monitoring Features

Describes how to use built-in self-monitoring features for diagnostics.

Appendix 1: Specifications

Appendix 1: Display Specifications

Lists the technical specifications for the ST70+ display unit.

Appendix 1: Keypad General Specifications

Provides general specifications applicable to all ST70+ keypad types.

Appendix 1: Instrument Keypad Specifications

Lists the specific dimensions and button functions for the Instrument keypad.

Appendix 2: Glossary

Appendix 2: Glossary Terms

Provides a glossary of terms and definitions used in the manual.

Index

Index: Manual Index

An alphabetical index to help locate specific topics within the manual.