Roland Fantom XR User Manual

212
Effects List
67: OD → FLANGER
(OVERDRIVE → FLANGER)
fig.MFX-67
68: OD → DELAY
(OVERDRIVE → DELAY)
fig.MFX-68
69: DST → CHORUS
(DISTORTION → CHORUS)
The parameters are essentially the same as in “66: OD
→
CHORUS,”
with the exception of the following two.
OD Drive
→
Dst Drive, OD Pan
→
Dst Pan
fig.MFX-69
70: DST → FLANGER
(DISTORTION → FLANGER)
The parameters are essentially the same as in “67: OD →
FLANGER,” with the exception of the following two.
OD Drive
→
Dst Drive, OD Pan
→
Dst Pan
fig.MFX-70
71: DST → DELAY
(DISTORTION → DELAY)
The parameters are essentially the same as in “68: OD
→
DELAY,”
with the exception of the following two.
OD Drive
→
Dst Drive, OD Pan
→
Dst Pan
fig.MFX-71
Cho Balance #
D100:0W–D0:100W Adjusts the volume balance be-
tween the sound that is sent
through the chorus (W) and the
sound that is not sent through the
chorus (D).
Level 0–127 Output Level
Parameter
Value Description
Od Drive #
0–127 Degree of distortion
Also changes the volume.
Od Pan # L64–63R Stereo location of the overdrive
sound
Fln Pre Delay 0.0–100.0 ms Adjusts the delay time from when
the direct sound begins until the
flanger sound is heard.
Fln Rate # 0.05–10.00 Hz, note Frequency of modulation
Fln Depth 0–127 Depth of modulation
Fln Feedback # -98– +98 % Adjusts the proportion of the
flanger sound that is fed back into
the effect. Negative (-) settings
will invert the phase.
Fln Balance # D100:0W–D0:100W Adjusts the volume balance be-
tween the sound that is sent
through the flanger (W) and the
sound that is not sent through the
flanger (D).
Level 0–127 Output Level
Parameter
Value Description
Od Drive #
0–127 Degree of distortion
Also changes the volume.
Od Pan # L64–63R Stereo location of the overdrive
sound
Delay Time 0–2600 ms, note Adjusts the delay time from the
direct sound until the delay
sound is heard.
Delay
Feedback #
-98– +98 % Adjusts the proportion of the
delay sound that is fed back into
the effect. Negative (-) settings
will invert the phase.
Delay HF Damp 200–8000 Hz,
BYPASS
Adjusts the frequency above
which sound fed back to the ef-
fect will be cut. If you do not
want to cut the high frequencies,
set this parameter to BYPASS.
Parameter
Value Description
L in
R in
Flanger
Overdrive
L out
R out
Balance W
Balance W
Balance D
Balance D
Feedback
L in
R in
Delay
Overdrive
L out
R out
Balance W
Balance W
Balance D
Balance D
Feedback
Delay Balance #
D100:0W–D0:100W Adjusts the volume balance be-
tween the sound that is sent
through the delay (W) and the
sound that is not sent through
the delay (D).
Level 0–127 Output Level
Parameter
Value Description
L in
R in
Chorus
Distortion
L out
R out
Balance W
Balance W
Balance D
Balance D
L in
R in
Flanger
Distortion
L out
R out
Balance W
Balance W
Balance D
Balance D
Feedback
L in
R in
Delay
Distortion
L out
R out
Balance W
Balance W
Balance D
Balance D
Feedback
Fantom-XR_r_e.book 212 ページ ２００６年４月４日 火曜日 午前１０時１４分

Roland Fantom XR Specifications

General

Brand	Roland
Model	Fantom XR
Category	Synthesizer
Language	English