SMC Networks SMC EZ Switch 10/100/1000 SMCGS8P-Smart User Manual

Name: SMC Networks SMC EZ Switch 10/100/1000 SMCGS8P-Smart
Brand: SMC Networks
Rating: 5 (1 reviews)

366 pages

To Next Page

To Previous Page

OMMAND

INE

NTERFACE

3-180

• If the target switch has also enabled LACP on the connected

ports, the trunk will be activated automatically.

• If more than four ports attached to the same target switch have

LACP enabled, the additional ports will be placed in standby

mode, and will only be enabled if one of the active links fails.

Example

The following shows LACP enabled on ports 10-11. Because LACP

has also been enabled on the ports at the other end of the links,

the show interfaces status port-channel 1 command shows that

Trunk 1 has been established.

Console(config)#interface ethernet 1/10

Console(config-if)#lacp

Console(config-if)#exit

Console(config)#interface ethernet 1/11

Console(config-if)#lacp

Console(config-if)#exit

Console(config)#interface ethernet 1/9

Console(config-if)#lacp

Console(config-if)#exit

Console(config)#exit

Console#show interfaces status port-channel 1

Information of Trunk 1

Basic information:

Port type: 1000T

Mac address: 00-00-11-11-22-2C

Configuration:

Name:

Port admin: Up

Speed-duplex: Auto

Capabilities: 10half, 10full, 100half, 100full, 1000full,

Flow control: Disabled

Port security: Disabled

Port security action: None

Current status:

Created by: lacp

Link status: Up

Port operation status: Up

Operation speed-duplex: 1000full

Flow control type: None

Member Ports: Eth1/9, Eth1/10, Eth1/11,

Console#

b_mgmt.book Page 180 Tuesday, July 8, 2003 5:24 PM

Questions and Answers:

D
David BraunJul 30, 2025
What to do if I cannot connect to my SMC Networks SMC EZ 10/100/1000 SMCGS8P-Smart Switch using Telnet?
- R
  Rebecca VaughnJul 30, 2025
  If you're unable to connect to your SMC Networks Switch via Telnet, it might be due to exceeding the maximum allowed concurrent Telnet sessions. Try connecting again later. Also, ensure you've configured the agent with a valid IP address, subnet mask, and default gateway. Verify that your management station has management VLAN access to the switch, with the default being VLAN 1. Double-check that you have a valid network connection to the switch and the port you're using hasn't been disabled, and inspect the network cabling between your management station and the switch.
A
Alexandra MccallAug 9, 2025
How to troubleshoot connection issues with SMC Networks SMC EZ 10/100/1000 SMCGS8P-Smart Switch via Web browser?
- M
  Matthew HutchinsonAug 9, 2025
  If you're experiencing connection issues with your SMC Networks Switch via a web browser, ensure that the agent is configured with a valid IP address, subnet mask, and default gateway. Confirm that your management station has management VLAN access to the switch (default is VLAN 1). Check that you have a valid network connection to the switch and that the port you are using has not been disabled. Also, check the network cabling between the management station and the switch.

SMC Networks SMC EZ Switch 10/100/1000 SMCGS8P-Smart Specifications

General

Ports	8
Port Type	10/100/1000 Mbps
Switching Capacity	16 Gbps
Forwarding Rate	11.9 Mpps
MAC Address Table Size	8K
Power over Ethernet (PoE)	Yes
Input Voltage	100-240VAC
Form Factor	Desktop/Rackmount
Features	VLAN, QoS, IGMP Snooping
Dimensions	280 x 180 x 44 mm
Operating Temperature	0°C to 40°C
Storage Temperature	-20°C to 70°C
Humidity	10% to 90% (non-condensing)
Jumbo Frame Support	Yes (9K bytes)