Sony SRG-A40 User Manual

27
Storing the Camera Settings
in Memory
– Preset Feature
Settings, including the camera position, zoom,
focus, and backlighting, can be stored in a
preset.
You can also store the presets from Web App or
VIS
CA/CGI commands.
Note
The camera supports up to 256 presets. The
number of presets that are supported will vary
depending on the device used.
– For the RM-IP500 (sold separately), up to 100.
– For the RM-IP10 (sold separately), up to 16.
– For the remote commander (supplied), up to 3.
– For a Web App, up to 100 positions.
– For VISCA command, up to 100.
– For CGI command, up to 256.
For details on the camera settings that can be
p
reset, see “Preset Items and Image Setting File
Items” (page 94).
Storing the camera status
1 Press the P/T RESET button to reset the
pan/tilt position.
2 Adjust the position, zoom, and focus of the
camera (See page 26).
3 Hold down the PRESET button and press
any of the 1 to 3 buttons, in which you want
to store the settings.
Note
Before you store the position, zoom, focus, etc.
of the camera, make sure to install and secure
the camera in place to use it properly.
Recalling the stored status
Press any of the 1 to 3 buttons in which you have
stored the settings.
Notes
• When the pan/tilt position is set to PRESET1,
the camera moves to the PRESET1 position at
startup.
• Storing or clearing the settings in PRESET 1
tak
es about 2 seconds longer than for other
preset operations.
• When you are storing or clearing the settings in
on
e PRESET, you cannot restore, store, or clear
the settings in another PRESET.
• For details on the items that can be cleared
fr
om the memory, see “Preset Items and Image
Setting File Items” (page 94).
• You can register or delete the preset even while
the
OSD menu is being displayed.
• Note that if you change the image flip setting,
the
set preset will be cleared.
• The supplied remote commander does not
h
ave the function to remove the preset
memories. Therefore, remove the memories
using Web App, VISCA/CGI commands, or the
remote controller (sold separately), or
overwrite the memory on the same position.
While holding
down
Press the
number button
you want to set.

Sony SRG-A40 Specifications

General

Megapixel	8.5 MP
Camera type	Single camera
Sensor type	CMOS
White balance	Auto, Indoor, One push, Outdoor
Zoom capability	Yes
Gain control type	Auto/Manual
Focal length range	4.4 - 88 mm
Optical sensor size	1/2.5 \
Aperture range (F-F)	2 - 3.8
Light exposure modes	Auto, Manual
Minimum illumination	1.6 lx
Maximum working distance (tele)	800 mm
Minimum working distance (wide)	80 mm
Maximum frame rate	60 fps
Video formats supported	H.264, H.265
Maximum video resolution	3840 x 2160 pixels
Supported graphics resolutions	640 x 480 (VGA), 1280 x 720 (HD 720), 1920 x 1080 (HD 1080)
Pan range	-170 - 170 °
Product color	White
Pan speed (max)	300 °/sec
Tilt angle range	-20 - 90 °
Tilt speed (max)	126 °/sec
Bit rate control	Constant Bit Rate (CBR), Variable Bit Rate (VBR)
Supported protocols	IPv4, IPv6, TCP, UDP, ARP, ICMP, HTTP, HTTPS, DHCP, DNS, RTP/RTCP, RTSP, VISCA over IP, SRT
Multi-stream capability	3
Audio channels	2
Ethernet LAN (RJ-45) ports	1
DC input voltage	19.5 V
Power source type	DC, PoE
Power consumption (typical)	80 W
Storage temperature (T-T)	-20 - 60 °C
Operating temperature (T-T)	0 - 40 °C
Number of screws	6

Weight and Dimensions

Depth	200 mm
Width	156.7 mm
Height	184 mm
Weight	2000 g