EasyManuals Logo

TP-Link TL-WA5210G User Manual

TP-Link TL-WA5210G
114 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #93 background imageLoading...
Page #93 background image
85
default setting is 0.0.0.0.
¾ Default Domain (optional) - Enter the domain name of the your DHCP server. You can
leave the field blank.
¾ Primary DNS (optional) - Enter the DNS IP address provided by your ISP. Consult your ISP
if you don’t know the DNS value. The factory default setting is 0.0.0.0.
¾ Secondary DNS (optional) - Enter the IP address of another DNS server if your ISP
provides two DNS servers. The factory default setting is 0.0.0.0.
Click Save to save the changes.
)
Note:
1) When the device is working on Dynamic IP mode, the DHCP Server function will be disabled.
2) To use the DHCP server function of the device, you should configure all computers in the
LAN as "Obtain an IP Address automatically" mode. This function will not take effect until the
device reboots.
5.7.2 DHCP Clients List
Selecting DHCP > DHCP Clients List will enable you to view the Client Name, MAC Address,
Assigned IP and Lease Time for each DHCP Client attached to the device (Figure 5-20).
Figure 5-20 DHCP Clients List
¾ ID - Here displays the index of the DHCP client.
¾ Client Name - Here displays the name of the DHCP client.
¾ MAC Address - Here displays the MAC address of the DHCP client.
¾ Assigned IP - Here displays the IP address that the AP has allocated to the DHCP client.
¾ Lease Time - Here displays the time of the DHCP client leased. Before the time is up, DHCP
client will request to renew the lease automatically.
You cannot change any of the values on this page. To update this page and to show the current
attached devices, click on the Refresh button.
5.7.3 Address Reservation
Selecting DHCP > Address Reservation will enable you to specify a reserved IP address for a
PC on the LAN, so the PC will always obtain the same IP address each time when it accesses the
AP. Reserved IP addresses should be assigned to servers that require permanent IP settings.
The screen below is used for address reservation (shown in Figure 5-21).

Table of Contents

Other manuals for TP-Link TL-WA5210G

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the TP-Link TL-WA5210G and is the answer not in the manual?

TP-Link TL-WA5210G Specifications

General IconGeneral
2.4 GHzYes
ModulationDBPSK, DSSS, OFDM, QPSK
Frequency band2.4 - 2.4835 GHz
Receiver sensitivity802.11g 54M: -76dBm 48M: -78dBm 36M: -82dBm 12M: -91dBm 9M:-92dBm, 802.11b 11M:-90dBm 5.5M:-92dBm 1M:-98dBm
Maximum data transfer rate54 Mbit/s
Networking featuresFast Ethernet
Vertical beam width60 °
Transmit power range20/27 dBm dBmW
Horizontal beam width30 °
Maximum operating distance50000 m
Compliance industry standardsIEEE 802.11g, IEEE 802.11b
Supported data transfer rates54/48/36/24/18/12/11/9/6/5.5/2/1 Mbps
Antenna connector typeRP-SMA
Antenna gain level (max)12 dBi
InternalNo
Ethernet LAN (RJ-45) ports1
Security algorithms128-bit WEP, 64-bit WEP, WPA, WPA-AES, WPA-PSK, WPA2, WPA2-PSK
Power requirements12VDC / 1.0A
Operating temperature (T-T)-30 - 70 °C
Storage relative humidity (H-H)5 - 95 %
Operating relative humidity (H-H)10 - 90 %
Weight and Dimensions IconWeight and Dimensions
Dimensions (WxDxH)265 x 120 x 83 mm

Related product manuals