Yamaha 2007 FZ6-NA User Manual

ELECTRICAL COMPONENTS
8-113
b. Connect the positive tester probe to termi-
nal “1” and the negative tester probe to ter-
minal “3”, and check the continuity.
c. If either of the readings indicate no continu-
ity, replace the bulb.
▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲
Checking the condition of the bulb sockets
The following procedure applies to all of the
bulb sockets.
1. Check:
• Bulb socket (for continuity)
(with the pocket tester)
No continuity → Replace.
NOTE:
Check each bulb socket for continuity in the
same manner as described in the bulb section;
however, note the following.
▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼
a. Install a good bulb into the bulb socket.
b. Connect the pocket tester probes to the
respective leads of the bulb socket.
c. Check the bulb socket for continuity. If any
of the readings indicate no continuity,
replace the bulb socket.
▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲
EAS4S81029
CHECKING THE LEDS
The following procedures applies to all of the
LEDs.
1. Check:
• LED (for proper operation)
Improper operation → Replace.
▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼
a. Disconnect the meter assembly coupler
(meter assembly side).
b. Connect two jumper leads “1” from the bat-
tery terminals to the respective coupler ter-
minal as shown.
WARNING
EWA4S81013
• A wire that is used as a jumper lead must
have at least the same capacity of the bat-
tery lead, otherwise the jumper lead may
burn.
• This check is likely to produce sparks,
therefore, make sure no flammable gas or
fluid is in the vicinity.
c. When the jumper leads are connected to
the terminals the respective LED should
illuminate.
Does not light → Replace the meter
assembly.
▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲
EAS28000
CHECKING THE FUSES
The following procedure applies to all of the
fuses.
CAUTION:
ECA13680
To avoid a short circuit, always set the main
switch to “OFF” when checking or replac-
ing a fuse.
1. Remove:
•Seat
• Front cowling inner panel
• Fuel tank (with ABS)
2. Check:
•Fuse
▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼
a. Connect the pocket tester to the fuse and
check the continuity.
NOTE:
Set the pocket tester selector to “Ω × 1”.
Pocket tester
90890-03112
Analog pocket tester
YU-03112-C

Yamaha 2007 FZ6-NA Specifications

General

Brand	Yamaha
Model	2007 FZ6-NA
Category	Motorcycle
Language	English