2.
When SP1 26 appears in the display, press the START (en-
ter) keypad. The current value will appear in the display.
NOTE: To go back to the current programmable
Special Vend 1 option without changing the value,
press the WARM (<) keypad.
3. Press the DELICATES (∧) or the COLD (∨) keypad to in-
crease or decrease to enable the desired options to be active
when the HEAVY keypad is active. Refer to Table 1.
4. Press the START (enter) keypad when the correct value ap-
pears in the display. The new value is saved and the next op-
tion will appear in the display.
Special Vend 2 Days Enable SP2
This option allows the owner to enable or disable a second spe-
cial vend. Special Vend 2 can be programmed using an external
device or network. The owner may also turn the Special Vend 2
option on or off.
1. Control must be in Manual Mode. Refer to How to Enter the
Manual Mode.
2. Press the DELICATES (∧) or the COLD (∨) keypad until
Prog appears in the display. Press the START (enter) keypad,
and AtS 1 will appear in the display.
3. Press the DELICATES (∧) or the COLD (∨) keypad to scroll
through the programmable options until SP2 appears in the
display.
4.
When SP2 appears in the display, press the START (enter)
keypad. The current Special Vend 2 Days Enable status will
appear in the display.
on = Option Enabled
oFF = Option Disabled (factory default setting)
5. Press the DELICATES (∧) or the COLD (∨) keypad to change
the current status.
6. Press the START (enter) keypad when the correct value ap-
pears in the display. The new value is saved and the next op-
tion will appear in the display.
Special Vend 3 Days Enable SP3
This option allows the owner to enable or disable third special
vend. Special Vend 3 can be programmed using an external de-
vice or network. The owner may also turn the Special Vend 3 op-
tion on or off.
1. Control must be in Manual Mode. Refer to How to Enter the
Manual Mode.
2. Press the DELICATES (∧) or the COLD (∨) keypad until
Prog appears in the display. Press the START (enter) keypad,
and AtS 1 will appear in the display.
3. Press the DELICATES (∧) or the COLD (∨) keypad to scroll
through the programmable options until SP3 appears in the
display.
4.
When SP3 appears in the display, press the START (enter)
keypad. The current Special Vend 3 Days Enable status will
appear in the display.
on = Option Enabled
oFF = Option Disabled (factory default setting)
5. Press the DELICATES (∧) or the COLD (∨) keypad to change
the current status.
6. Press the START (enter) keypad when the correct value ap-
pears in the display. The new value is saved and the next op-
tion will appear in the display.
Special Vend 4 Days Enable SP4
This option allows the owner to enable or disable a fourth special
vend. Special Vend 4 can be programmed using an external de-
vice or network. The owner may also turn the Special Vend 4 op-
tion on or off if desired.
1. Control must be in Manual Mode. Refer to How to Enter the
Manual Mode.
2. Press the DELICATES (∧) or the COLD (∨) keypad until
Prog appears in the display. Press the START (enter) keypad,
and AtS 1 will appear in the display.
3. Press the DELICATES (∧) or the COLD (∨) keypad to scroll
through the programmable options until SP4 appears in the
display.
4.
When SP4 appears in the display, press the START (enter)
keypad. The current Special Vend 4 Days Enable status will
appear in the display.
on = Option Enabled
oFF = Option Disabled (factory default setting)
5. Press the DELICATES (∧) or the COLD (∨) keypad to change
the current status.
6. Press the START (enter) keypad when the correct value ap-
pears in the display. The new value is saved and the next op-
tion will appear in the display.
Cycle Modifier Programming CNP-
This option allows the owner to program the machine to offer ex-
tra wash time, extra rinse time, a warm rinse, or any combination
of the above to the customers for an added vend price. This op-
tion is used when MEDIUM or HEAVY is selected using the
Modifier keypad.
How to Program Default Cycle Modifier CNP 1
This option allows the owner to set the Default Cycle Modifier.
1. Control must be in Manual Mode. Refer to How to Enter the
Manual Mode.
2. Press the DELICATES (∧) or the COLD (∨) keypad until
Prog appears in the display. Press the START (enter) keypad,
and AtS 1 will appear in the display.
Programming Control
©
Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
58 Part No. 204370ENR1
To Next Page
Loading...
Need help?
General