PF rst
DISPLAY TO ENTER IN
STEP 6
POWER FAIL RESET
TIME
oFF *
Turned OFF. Cycle will be
saved.
0 - 120
Number in minutes
0 - 120 minutes without pow-
er before cycle is lost
* Factory default setting.
Table 11
IR Access IrA En
This option allows the owner to enable or disable allowing the
control to be communicated with by an external IR device.
1. Control must be in Manual Mode. Refer to How to Enter the
Manual Mode.
2. Press the DELICATES (∧) or the COLD (∨) keypad until
Prog appears in the display. Press the START (enter) keypad,
and AtS 1 will appear in the display.
3. Press the DELICATES (∧) or the COLD (∨) keypad to scroll
through the programmable options until IrA En appears in
the display.
4.
When IrA En appears in the display, press the START (en-
ter) keypad. The current IR Access status will appear in the
display.
on = Option Enabled (factory default setting)
oFF = Option Disabled
5. Press the DELICATES (∧) or the COLD (∨) keypad to change
the current status.
6. Press the START (enter) keypad when the correct value ap-
pears in the display. The new value is saved and the next op-
tion will appear in the display.
Manual Rapid Advance rAPdEn
This option allows the owner to enable or disable the rapid ad-
vance feature. Refer to Rapid Advance Feature section for more
information.
1. Control must be in Manual Mode. Refer to How to Enter the
Manual Mode.
2. Press the DELICATES (∧) or the COLD (∨) keypad until
Prog appears in the display. Press the START (enter) keypad,
and AtS 1 will appear in the display.
3. Press the DELICATES (∧) or the COLD (∨) keypad to scroll
through the programmable options until rAPdEn appears in
the display.
4.
When rAPdEn appears in the display, press the START (en-
ter) keypad. The current Manual Rapid Advance status will
appear in the display.
0 = oFF (access requires password)
1 = on (access allowed) (factory default setting)
2 = DISABLED (access not allowed)
5. Press the DELICATES (∧) or the COLD (∨) keypad to change
the current status.
6. Press the START (enter) keypad when the correct value ap-
pears in the display. The new value is saved and the next op-
tion will appear in the display.
Manual Diagnostics diAgEn
This option allows the owner to enable or disable the manual di-
agnostics option. Refer to Testing Machine and Electronic Con-
trol Functions section for more information.
1. Control must be in Manual Mode. Refer to How to Enter the
Manual Mode.
2. Press the DELICATES (∧) or the COLD (∨) keypad until
Prog appears in the display. Press the START (enter) keypad,
and AtS 1 will appear in the display.
3. Press the DELICATES (∧) or the COLD (∨) keypad to scroll
through the programmable options until diAgEn appears in
the display.
4.
When diAgEn appears in the display, press the START (en-
ter) keypad. The current Manual Diagnostics status will ap-
pear in the display.
0 = oFF (access requires password)
1 = on (access allowed) (factory default setting)
2 = DISABLED (access not allowed)
5. Press the DELICATES (∧) or the COLD (∨) keypad to change
the current status.
6. Press the START (enter) keypad when the correct value ap-
pears in the display. The new value is saved and the next op-
tion will appear in the display.
Factory Test Ft En
This option allows the owner to enable or disable access to Facto-
ry Test.
1. Control must be in Manual Mode. Refer to How to Enter the
Manual Mode.
2. Press the DELICATES (∧) or the COLD (∨) keypad until
Prog appears in the display. Press the START (enter) keypad,
and AtS 1 will appear in the display.
3. Press the DELICATES (∧) or the COLD (∨) keypad to scroll
through the programmable options until Ft En appears in the
display.
Programming Control
©
Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
63 Part No. 204370ENR1
To Next Page
Loading...
Need help?
General