ALLIANCE SWNNX2SP115TW01 User Manual

3. Press the DELICATES (∧) or the DELICATES (∨) keypad to
scroll through the programmable options until CNP- appears
in the display.
4.
When CNP- appears in the display, press the START (enter)
keypad.
5. Press the DELICATES (∧) or the COLD (∨) keypad to scroll
through the programmable Cycle Modifier options until CNP
1 appears in the display.
6.
When CNP 1 appears in the display, press the START (enter)
keypad. A number will appear in the display. This number
corresponds to the current default cycle modifier. Refer to ta-
ble below.
CNP 1
Default Value Cycle Modifier
0* LIGHT
1 MEDIUM
2 HEAVY
*Factory default setting.
Table 9
7. Press the DELICATES (∧) or the COLD (∨) keypad to in-
crease or decrease the current number to the desired number
selected from the table.
8. Press the START (enter) keypad when the correct value ap-
pears in the display. The new value is saved and the next op-
tion will appear in the display.
How to Program Cycle Modifier MEDIUM Key #1
Options CNP 2
This option allows the owner to select the options that are ena-
bled when the MEDIUM modifier keypad is active.
1. Control must be in Manual Mode. Refer to How to Enter the
Manual Mode.
2. Press the DELICATES (∧) or the COLD (∨) keypad until
Prog appears in the display. Press the START (enter) keypad,
and AtS 1 will appear in the display.
3. Press the DELICATES (∧) or the COLD (∨) keypad to scroll
through the programmable options until CNP- appears in the
display.
4.
When CNP- appears in the display, press the START (enter)
keypad.
5. Press the DELICATES (∧) or the COLD (∨) keypad to scroll
through the programmable options until CNP 2 appears in the
display.
6.
When CNP 2 appears in the display, press the START (enter)
keypad.
NOTE: To go back to the current programmable op-
tion without changing the value, press the WARM (<)
keypad.
7. Press the DELICATES (∧) or the COLD (∨) keypad to change
the configuration value. Refer to the table below for the value
definitions.
8. Press the START (enter) keypad when the correct value ap-
pears in the display. The new value is saved and the next op-
tion will appear in the display.
Cycle Modifier Value Warm Rinse
0 * OFF
1 ON
* Factory default setting
Table 10
How to Program Cycle Modifier HEAVY Key #2
Options CNP 3
This option allows the owner to select the options that are ena-
bled when the HEAVY modifier keypad is active.
1. Control must be in Manual Mode. Refer to How to Enter the
Manual Mode.
2. Press the DELICATES (∧) or the COLD (∨) keypad until
Prog appears in the display. Press the START (enter) keypad,
and AtS 1 will appear in the display.
3. Press the DELICATES (∧) or the COLD (∨) keypad to scroll
through the programmable options until CNP- appears in the
display.
4.
When CNP- appears in the display, press the START (enter)
keypad.
5. Press the DELICATES (∧) or the COLD (∨) keypad to scroll
through the programmable options until CNP 3 appears in the
display.
6.
When CNP 3 appears in the display, press the START (enter)
keypad.
NOTE: To go back to the current programmable op-
tion without changing the value, press the WARM (<)
keypad.
7. Press the DELICATES (∧) or the COLD (∨) keypad to change
the configuration value.
8. Press the START (enter) keypad when the correct value ap-
pears in the display. The new value is saved and the next op-
tion will appear in the display.
How to Program Cycle Modifier MEDIUM
Additional Wash Time CNP 4
This option allows the owner to add additional time to agitate
steps that have wash selected as their status. The additional wash
time option needs to be turned on for the Cycle Modifier MEDI-
UM Additional Wash Time to take effect.
Programming Control
©
Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
59 Part No. 204370ENR1

ALLIANCE SWNNX2SP115TW01 Specifications

General

Brand	ALLIANCE
Model	SWNNX2SP115TW01
Category	Washer
Language	English