1. Control must be in Manual Mode. Refer to How to Enter the
Manual Mode.
2. Press the DELICATES (∧) or the COLD (∨) keypad until
Prog appears in the display. Press the START (enter) keypad,
and AtS 1 will appear in the display.
3. Press the DELICATES (∧) or the COLD (∨) keypad to scroll
through the programmable options until CNP- appears in the
display.
4.
When CNP- appears in the display, press the START (enter)
keypad.
5. Press the DELICATES (∧) or the COLD (∨) keypad to scroll
through the programmable options until CNP 4 appears in the
display.
6.
When CNP 4 appears in the display, press the START (enter)
keypad. A number will appear in the display corresponding to
the number of minutes to be added to agitate steps that have
wash selected as their status.
7. Press the DELICATES (∧) or the COLD (∨) keypad to in-
crease or decrease the current number minutes.
8. Press the START (enter) keypad when the correct value ap-
pears in the display. The new value is saved and the next op-
tion will appear in the display.
How to Program Cycle Modifier MEDIUM
Additional Extra Rinse Time CNP 5
This option allows the owner to add additional agitate time to ex-
tra rinse steps. The additional rinse time option needs to be turned
on for the Cycle Modifier MEDIUM Additional Extra Rinse
Time to take effect.
1. Control must be in Manual Mode. Refer to How to Enter the
Manual Mode.
2. Press the DELICATES (∧) or the COLD (∨) keypad until
Prog appears in the display. Press the START (enter) keypad,
and AtS 1 will appear in the display.
3. Press the DELICATES (∧) or the COLD (∨) keypad to scroll
through the programmable options until CNP- appears in the
display.
4.
When CNP- appears in the display, press the START (enter)
keypad.
5.
When CNP 5 appears in the display, press the START (enter)
keypad. A number will appear in the display corresponding to
the number of minutes to be added to steps that have Rinse 1
selected as their status.
6. Press the DELICATES (∧) or the COLD (∨) keypad to in-
crease or decrease the current number of minutes.
NOTE: To go back to the current programmable op-
tion without changing the value, press the WARM (<)
keypad.
7. Press the START (enter) keypad when the correct value ap-
pears in the display. The new value is saved and the next op-
tion will appear in the display.
How to Program Cycle Modifier HEAVY Additional
Wash Time CNP 6
This option allows the owner to add additional time to agitate
steps that have wash selected as their status. The additional wash
time option needs to be turned on for the Cycle Modifier HEAVY
Additional Wash Time to take effect.
1. Control must be in Manual Mode. Refer to How to Enter the
Manual Mode.
2. Press the DELICATES (∧) or the COLD (∨) keypad until
Prog appears in the display. Press the START (enter) keypad,
and AtS 1 will appear in the display.
3. Press the DELICATES (∧) or the COLD (∨) keypad to scroll
through the programmable options until CNP- appears in the
display.
4.
When CNP- appears in the display, press the START (enter)
keypad.
5. Press the DELICATES (∧) or the COLD (∨) keypad to scroll
through the programmable options until CNP 6 appears in the
display.
6.
When CNP 6 appears in the display, press the START (enter)
keypad. A number will appear in the display corresponding to
the number of minutes to be added to steps that have Wash se-
lected as their status.
7. Press the DELICATES (∧) or the COLD (∨) keypad to in-
crease or decrease the current number of minutes.
8. Press the START (enter) keypad when the correct value ap-
pears in the display. The new value is saved and the next op-
tion will appear in the display.
How to Program Cycle Modifier HEAVY Additional
Extra Rinse Time CNP 7
This option allows the owner to add additional agitate time to ex-
tra rinse steps. The additional rinse time option needs to be turned
on for the Cycle Modifier HEAVY Additional Extra Rinse Time
to take effect.
1. Control must be in Manual Mode. Refer to How to Enter the
Manual Mode.
2. Press the DELICATES (∧) or the COLD (∨) keypad until
Prog appears in the display. Press the START (enter) keypad,
and AtS 1 will appear in the display.
3. Press the DELICATES (∧) or the COLD (∨) keypad to scroll
through the programmable options until CNP- appears in the
display.
4.
When CNP- appears in the display, press the START (enter)
keypad.
5. Press the DELICATES (∧) or the COLD (∨) keypad to scroll
through the programmable options until CNP 7 appears in the
display.
6.
When CNP 7 appears in the display, press the START (enter)
keypad. A number will appear in the display corresponding to
Programming Control
©
Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
60 Part No. 204370ENR1
To Next Page
Loading...
Need help?
General