Cisco WAP150 User Manual

Uncheck Password Complexity to disable the password security rules. However, we strongly recommend
keeping the password security rules enabled. For more information about passwords, see Security, on page
39.
Note
Step 13 Click Next. The Configure Radio 1 - Name Your Wireless Network window appears.
Step 14 Enter a Network Name. This name serves as the SSID for the default wireless network.
Step 15 Click Next. The Configure Radio 1 - Secure Your Wireless Network window appears.
Step 16 Choose a security encryption type and enter a security key. For a description of these options, see Configuring Security
Settings, on page 54.
Step 17 Click Next. The Configure Radio 1 - Assign the VLAN ID for your Wireless Network window appears.
Step 18 Choose the VLAN ID for traffic received on the wireless network.
We recommend that you assign a different VLAN ID from the default (1) to the wireless traffic, in order to segregate
it from the management traffic on VLAN 1.
Step 19 Click Next. Repeat the step 13 to step 18 to configure the settings for Radio 2 interface.
Step 20 Click Next. The Enable Captive Portal - Create Your Guest Network window appears.
Step 21 Select whether or not to set up an authentication method for guests on your network, and click Next.
If you click No, skip to Step 29.
If you click Yes, the Enable Captive Portal - Name Your Guest Network window appears.
Step 22 Specify a Guest Network Name.
Step 23 Click Next. The Enable Captive Portal - Secure Your Guest Network window appears.
Step 24 Choose a security encryption type for the guest network and enter a security key. For a description of these options,
see Configuring Security Settings, on page 54.
Step 25 Click Next. The Enable Captive Portal - Assign the VLAN ID window appears.
Step 26 Specify a VLAN ID for the guest network. The guest network VLAN ID should be different from the management
VLAN ID.
Step 27 Click Next. The Enable Captive Portal - Enable Redirect URL window appears.
Step 28 Check Enable Redirect URL and enter a fully qualified domain name (FQDN) or IP address in the Redirect URL
field (including https://). If specified, the guest network users are redirected to the specified URL after authenticating.
Step 29 Click Next. The Summary - Confirm Your Settings window appears.
Step 30 Review the settings that you configured. Click Back to reconfigure one or more settings. If you click Cancel, all settings
are returned to the previous or default values.
Step 31 If they are correct, click Submit. Your setup settings are saved and a confirmation window appears.
Step 32 Click Finish.
The WAP device was configured successfully. You are required to log in again with the new password.
Using the Access Point Setup Wizard with mobile
The first time that you log into the Access Point with your portable device or after it has been reset to the
factory default setting, the Access Point Setup Wizard with mobile style appears. This helps you perform the
initial configurations. To configure the Access Point using the wizard, complete the following steps:
Cisco WAP150 Wireless-AC/N Dual Radio Access Point with PoE / Cisco WAP361 Wireless-AC/N Dual Radio Wall Plate Access Point with PoE
4
Getting Started
Using the Access Point Setup Wizard with mobile

Cisco WAP150 Specifications

General

VLAN support	Yes
Number of users	64 user(s)
Networking standards	IEEE 802.11ac, IEEE 802.11b, IEEE 802.11e, IEEE 802.11g, IEEE 802.11i, IEEE 802.11n, IEEE 802.1Q, IEEE 802.1x, IEEE 802.3af, IEEE 802.3u
Ethernet LAN data rates	10, 100, 1000 Mbit/s
Maximum data transfer rate	1200 Mbit/s
Antenna type	Internal
Placement	Table, Wall
Cable lock slot type	Kensington
Security algorithms	HTTPS, SSID, WPA, WPA2
Service Set Identifier (SSID) features	SSID broadcast on/off
Storage temperature (T-T)	-20 - 70 °C
Operating temperature (T-T)	0 - 40 °C
Storage relative humidity (H-H)	5 - 90 %
USB 2.0 ports quantity	0

Weight and Dimensions

Depth	38 mm
Width	135 mm
Weight	350 g