Cisco WAP150 User Manual

Step 2 Check the Enable checkbox to enable Spanning Tree.
Step 3 Click Spanning Tree Settings to configure the spanning tree protocol for each port.
• Flood BPDU if STP is disabled on port(s)—Check to flood the BPDU packets received from the port(s) whose
STP status is disabled, or uncheck to drop the BPDU packets received from the port(s) whose STP status is disabled.
• LAN0 ~4/WDS0 ~3—Check to enable STP on a port, or uncheck to disable STP on a port.
VLANs Setting
Use the VLAN Configuration page to view and configure the VLANs settings.
Step 1 Select LAN > More > VLANs Setting Table.
Step 2 Configure these parameters:
• Untagged VLAN ID — Specifies a number between 1 and 4094 for the untagged VLAN ID. The default is 1. The
traffic on the VLAN that you specify in this field is not be tagged with a VLAN ID when forwarded to the network.
• Description — Description of the related VLAN.
• Management VLAN — The Management VLAN is the VLAN used to access the WAP device through Telnet or
the web GUI. There must be only one VLAN as the management VLAN. If no interface (wired or wireless) is
assigned to the Management VLAN, there will be no interface that a user can use to access the configuration utility.
• VLAN — Select from the drop-down list (Untagged or Tagged) VLAN.
By default, all traffic on the WAP device uses the VLAN 1, the default untagged VLAN. This means that all traffic
is untagged until you disable the untagged VLAN, change the untagged traffic VLAN ID, or change the VLAN ID
for a VAP or client using RADIUS.
Step 3 Click Apply. The changes are saved to the Startup Configuration.
Neighbor Discover
Bonjour enables the WAP device and its services to be discovered by using multicast DNS (mDNS). Bonjour
advertises services to the network and answers queries for the service types that it supports, simplifying
network configuration in your environments.
The WAP device advertises these service types:
• Cisco-specific device description (csco-sb) — This service enables clients to discover the Cisco WAP
devices and other products deployed in your networks.
• Management user interfaces — This service identifies the management interfaces available on the
WAP device (HTTP and SNMP).
When a Bonjour-enabled WAP device is attached to a network, any Bonjour client can discover and get access
to the configuration utility without prior configuration.
Cisco WAP150 Wireless-AC/N Dual Radio Access Point with PoE / Cisco WAP361 Wireless-AC/N Dual Radio Wall Plate Access Point with PoE
21
System Configuration
VLANs Setting

Cisco WAP150 Specifications

General

VLAN support	Yes
Number of users	64 user(s)
Networking standards	IEEE 802.11ac, IEEE 802.11b, IEEE 802.11e, IEEE 802.11g, IEEE 802.11i, IEEE 802.11n, IEEE 802.1Q, IEEE 802.1x, IEEE 802.3af, IEEE 802.3u
Ethernet LAN data rates	10, 100, 1000 Mbit/s
Maximum data transfer rate	1200 Mbit/s
Antenna type	Internal
Placement	Table, Wall
Cable lock slot type	Kensington
Security algorithms	HTTPS, SSID, WPA, WPA2
Service Set Identifier (SSID) features	SSID broadcast on/off
Storage temperature (T-T)	-20 - 70 °C
Operating temperature (T-T)	0 - 40 °C
Storage relative humidity (H-H)	5 - 90 %
USB 2.0 ports quantity	0

Weight and Dimensions

Depth	38 mm
Width	135 mm
Weight	350 g