gefran GRM-H 15 User Manual

819XX_MAN_GRM-H_11-2022_ENG_pag. 4
5.5.1.3. Dryout power ...................................................56
5.5.1.4. Dryout phase restart command .......................56
5.5.1.5. Dryout phase end command ...........................56
5.5.1.6. Dryout phase status ......................................... 56
5.5.1.7. Communication error mode .............................57
5.5.1.8. Communication error timeout ..........................57
5.5.1.9. Communication error power ............................57
5.5.1.10. ìInductive load on .............................................58
5.5.1.11. Start modes ......................................................58
5.5.1.12. Manual power saving ....................................... 58
5.5.1.13. Automatic/Manual status ................................. 59
5.5.1.14. Manual power percentage value ...................... 59
5.5.1.15. Percent value of delivered power .....................59
5.6. Power control ......................................................................60
5.6.1.1. Trigger modes ..................................................60
5.6.1.2. Phase Angle (PA) Mode ....................................61
5.6.1.3. Softstart ...........................................................62
5.6.1.4. Trigger modes ..................................................63
5.6.1.5. Minimum number of Burst Firing cycles ..........63
5.6.1.6. SSR output cycle time .....................................63
5.6.1. Soft start ramp settings ............................................ 64
5.6.1.1. Soft start enabling ............................................ 64
5.6.1.2. Soft start ramp duration ................................... 64
5.6.1.3. Soft start ramp reactivation time ......................64
5.6.1.4. Enabling softstart at shutdown ........................65
5.6.1.5. Soft start ramp status ......................................65
5.6.2. Current limit settings ................................................. 65
5.6.2.1. Peak current limiter during softstart .................65
5.6.2.2. Maximum peak current during softstart ........... 66
5.6.2.3. RMS steady state current control ....................66
5.6.2.4. Maximum RMS current at steady state ...........67
5.6.3. Triggering delay settings (triggering delay) ............... 67
5.6.3.1. Enable triggering delay ....................................67
5.6.3.2. Triggering delay ................................................ 67
5.6.3.3. Minimum non-conduction time to reactivate
triggering delay ................................................68
5.6.3.4. Minimum trigger power .................................... 68
5.6.3.5. Control output gradient .................................... 68
5.6.4. Feedback mode ........................................................ 69
5.6.4.1. Enabling feedback mode .................................70
5.6.4.2. Voltage feedback reference .............................70
5.6.4.3. Current feedback reference .............................70
5.6.4.4. Power feedback reference ...............................70
5.6.4.5. Impedance feedback reference .......................71
5.6.4.6. Feedback response speed ...............................71
5.6.4.7. Feedback calibration command ......................71
5.6.4.8. Feedback reference .........................................72
5.6.4.9. Power correction for feedback .........................72
5.7. Hardware and Software Information ...................................73
5.7.4.1. Software version ..............................................73
5.7.4.2. Manufacturer identifier .....................................73
5.7.4.3. Model identifier ................................................73
5.7.4.4. Serial number .................................................. 73
5.7.4.5. Product code (Fxxxxxx order code) ................. 74
5.7.4.6. Last modification user ......................................74
5.7.4.7. Hardware card recognition ............................... 74
5.7.4.8. Hardware card recognition 1 ............................ 75
5.7.4.9. Options installed ..............................................75
6. IO-Link ............................................................ 76
6.1. IO-Link .................................................................................76
6.2. IO-LINK INSTALLATION AND ELECTRICAL CONNECTIONS
76
6.2.1. Electrical installation ................................................. 76
6.3. CONTROL MODE ................................................................77
6.3.1. IO-Link information ................................................... 77
6.3.2. SIO mode and IO-Link mode .................................... 78
6.3.3. Process data mapping .............................................. 78
6.3.4. Setting data ............................................................... 79
7. TECHNICAL SPECIFICATIONS ..................... 88
7.1. Technical specifications ......................................................88
7.2. Derating curves ...................................................................91
7.3. Downgrade with installation distance .................................92
7.4. Extrarapid fuses ..................................................................93
7.5. Accessoires ......................................................................... 93
7.6. Fans (for 90A/120A models only) ........................................93
7.7. Order code ..........................................................................94
7.8. EMC standards ...................................................................95
7.9. Warnings .............................................................................96
8. CERTIFICATIONS .......................................... 96
8.1. Certifications .......................................................................96

gefran GRM-H 15 Specifications

General

Brand	gefran
Model	GRM-H 15
Category	Controller
Language	English