2. Program Change How to Use the Basic Program
22
NFS-640 Programming Manual P/N 51333:B 10/03/2003
How to Modify an Addressable Detector Point
This section contains a sample detector programming screen, detector default selection, and instructions
for modifying a detector point. Autoprogram default values for a detector are shown:
Table 4 Detector Program Values
12 spaces for extended custom label
PROGRM SMOKE(PHOTO) DETECTOR ADDR 2D101
03 __ __ __ __A8P8AV 2D101
Blinking Type Code selection
CBE list
(five zones)
D (detector)
SLC address (001-159)
20-character user-editable custom label (in
this example, autoprogramming has used
the first 19 and left a space at the end.)
SLC Loop number
Alarm sensitivity level
Pre-alarm sensitivity level
Cooperative multi-detector
mode indicator
Alarm verification setting
Field Description Set as Follows
Type Code Detector function specification -
SMOKE(PHOTO) in example.
Press the
NEXT or PREVIOUS Selection keys to scroll through valid detector Type
Code selections. See Table 32 on page 104 for lists and descriptions.
Custom Label 20 character custom label. Change by placing the cursor into the first space of the field using the arrow keys,
then typing the descriptor. DETECTOR ADDR 2D101 is the autoprogram default
custom label for the detector at address 101 on SLC 2.
Extended Label 12 character custom label
extension.
See “Custom Label” above.
Note: Spaces must be input by the user, including any space necessary between the
custom and extended label fields. An 80-column printout will run the two fields
together.
CBE List Five zones can be listed - one
zone, Z03, is shown in the
example. Up to 4 more could be
added to this detector.
Zones can be changed or added to the CBE list by placing the cursor in the zone
field using arrow keys, then typing.
Defaults:
Alarm
Sensitivity
The alarm sensitivity level, with 9
the least sensitive alarm level and
1 the most sensitive alarm level.
Refer to Table 30 on page 90 for settings. Select by placing the cursor in the field
using the arrow keys, then either pressing the
NEXT or PREVIOUS keys to make the
selection, or typing the value.
Defaults:
Pre-alarm level Shows the Pre-Alarm level
setting—a number between 0 and
9—as follows:
0 – no Pre-Alarm
1 – self optimizing
2 – most sensitive Pre-Alarm level
9 – least sensitive Pre-Alarm level
Refer to Table 30 on page 90 for settings. Select by placing the cursor in the field
using the arrow keys, then either pressing the
NEXT or PREVIOUS keys to make the
selection, or typing the value.
Defaults:
Cooperative
Multi-detector
mode
Indicates the cooperative
multi-detector mode (A in the
example).
Select by placing the cursor in the field using the arrow keys, then either pressing
the
NEXT or PREVIOUS keys to make the selection, or typing the value.
* = OFF (Default)
A combines the detector's alarm decision with the next address above
B combines the detector's alarm decision with the next address below
C combines the detector's alarm decision with the next address above and the next
address below
Alarm
verification
Indicates the alarm verification
setting (V in the example).
Indicates Alarm Verification (V=on, *=off). Select by placing the cursor in the field
using the arrow keys, then pressing the
NEXT or PREVIOUS keys to make the
selection. Refer to “How to Interpret a Detector Status Display or Maintenance
Report” on page 93 for more information on the alarm verification feature.
Zone 01 (Heat detectors)
Zone 02 (Ion detectors)
Zone 03 (Photo detectors)
Zone 04 (Laser detectors)
Zone 05 (Multisensor)
A8 (Photo)
A6 (Ion)
A6 (Laser )
A5
Multisensor
P8 (Photo)
P6 (Ion)
P6 (Laser)
P5 (Multisensor)
www.PDF-Zoo.com
To Next Page
Loading...
Need help?
General
