PROG. B
PROG. A
PROG. A
PROG. B
actual
recording
PROG. A
PROG. C PROG. B
PROG. C
The first 2 minutes (at the longest) will be cut off.
When the recording time is partially overlapped:
PROG. A will start after PROG. B is complete to
be recorded.
PROG. A
PROG. B
PROG.B PROG.A
The first 2 minutes (at the longest) will be cut off.
PROG. A
PROG. B
PROG. B
When the recording time is entirely overlapped:
PROG.A will not be recorded.
PROG. A
PROG. B
actual
recording
The first 2 minutes (at the longest) will be cut off
(when recording to DVD only).
When the starting time is the same:
A program set previously (PROG. A) has priority.
When the starting time and the ending time
for each programs are different:
A program that has earlier start time (PROG.C)
has priority.
actual
recording
actual
recording
•
Timerprogramwhichhastheearlierstarttimewillbeplacedrstinthetimerprogramlist,andbegivenpriorityover
the programs with the later start time when timer programs overlap.
•
Whentimerprogramsoverlap,therst2minutes(atthelongest)ofthelaterrecordingwillbecutoff.
•
When2ormoretimerprogramshavethesamestarttime,theprogramsetrstwillbegivenpriority.
•
A timer recording of lower priority will be cancelled or start from the middle.
•
Check the overlapped timer programmings and change the priority if necessary.
The Priority of Overlapped Settings
Note for DVD recording
•
When the recording time of 2 programs are overlapped or
the end time of a program and the start time of another
programisthesame,therst2minutes(atthelongest)of
the subsequent program will be cut off.
•
If the cut-off portion comes up to 3 minute or more, this
program will be displayed with error number E40 in the timer
programming list.
•
If there is a power failure or this unit has been
unplugged for more than 30 seconds, the clock setting
and all timer programming will be lost.
•
If a disc is not inserted, "DVD" on the front panel display
ashesandtimerrecordingcannotbeperformed.In
some cases,
will appear momentarily around the
start time as the unit attempts to record. Please insert a
recordable disc.
•
If a cassette tape with a erase-protection tab is not
in the cassette compartment or there is no cassette
tape in the cassette compartment, “VCR” on the front
paneldisplayashesandtimerrecordingcannotbe
performed. Please insert a recordable cassette tape.
•
If a cassette tape ends during the timer recording, the
unit will automatically stop, eject the cassette tape, and
turn itself to the standby mode. To continue recording,
insert a recordable tape.
•
When all the timer recordings are completed,
ashes.Press[TIMER SET] to release the unit from the
timer standby mode.
•
If both DVD and VCR are timer programmed, you cannot
use any functions for either unit during timer standby or
timer recording. If you want to use functions other than
recording under such condition, cancel timer recording
by pressing [TIMER SET] during timer standby or stop
recording by pressing [C ] / [C A] on the front panel of
the unit during timer recording.
•
To cancel the timer standby mode, press [TIMER SET].
•
When the starting and the ending time are the same,
“Exceeds 12 hours” appears and the program setting
will not be accepted.
•
When the disc or cassette tape becomes full during the
recording, the unit turns itself to the standby mode.
•
If the starting time is earlier and the ending time is later
than the current time, the recording will start right after
you press [TIMER SET] at step 9 on page 32.
•
The timer recording cannot be performed in DVD and
VCR at the same time. If you set 2 programmings with
the same channel and time in both devices, the program
whichissetrstwillhavethepriority.
•
“Press TIMER SET for timer recording” will appear
on the TV screen 5 minutes before the programmed
starting time.
To Next Page
Loading...
Need help?
General
