Siemens SINUMERIK 808D ADVANCED Parameter Manual

Active: The change in the data becomes active on the start of the upload for the next
range.
The settings are only active, if MD11212 $MN_UPLOAD_CHANGES_ONLY=FALSE.
11212 UPLOAD_CHANGES_ONLY N01, N05 -
- Data backup type for an active file system. BOOLEAN Immediately
-
- - TRUE - - 2/2
Description: Only values of the selected file of the active file system
that deviate from the default setting are backed up.
TRUE = only the values of the selected file of the active file system that deviate
from the standard setting are backed up (a differential data backup)
The value of MD11210 $MN_UPLOAD_MD_CHANGES_ONLY than has no effect.
FALSE = all values of the selected file of the active file system are backed up.
Same significance as MD11210 $MN_UPLOAD_MD_CHANGES_ONLY=0.
However, if MD11210 $MN_UPLOAD_MD_CHANGES_ONLY is not equal to 0, then this
setting is active.
11240 PROFIBUS_SDB_NUMBER N01, N05 K4, FBU
- SDB number DWORD PowerOn
-
808d-me42 4 -1, -1, -1, -1 -1, -1, -1, -1 7, 7, 7, 7 2/2
808d-me62 4 0, -1, -1, -1 -1, -1, -1, -1 7, 7, 7, 7 2/2
808d-te42 4 -1, -1, -1, -1 -1, -1, -1, -1 7, 7, 7, 7 2/2
808d-te62 4 0, -1, -1, -1 -1, -1, -1, -1 7, 7, 7, 7 2/2
808d-mte40 4 -1, -1, -1, -1 -1, -1, -1, -1 7, 7, 7, 7 2/2
808d-mte60 4 0, -1, -1, -1 -1, -1, -1, -1 7, 7, 7, 7 2/2
Description: Number of the system data block (SDB) used for configuring the I/Os.
The following assignments of MD11240[0,1,2,3] are prmitted:
[0, -1, 0, 0] telegram 136 and axis extension NX10.3
[1, -1, 1, 1] telegram 136 and axis extension NX15.3 (= default)
[2, -1, 2, 2] telegram 136 and axis extension NX15.3, 1x CU320-2 PN (only PPU 26x.3/28x.
3)
[3, -1, 3, 3] telegram 116 and axis extension NX10.3
[4, -1, 4, 4] telegram 136 and axis extension NX15.3, 1x CU310-2 PN (only PPU 26x.3/28x.
3)
[5, -1, 5, 5] telegram 136 and axis extension NX15.3, 2x CU310-2 PN (only PPU 26x.3/28x.
3)
11294 SIEM_TRACEFILES_CONFIG EXP -
- Configuration of the SIEM* trace file DWORD PowerOn
-
- - 0 0 0x7FFFFFFF 1/1
Description: Configuration of the tracefiles SIEM*
Bit0:
Additional information about the PDUs sent is to be entered in _N_SIEMDOMAINSEQ_MPF
for download
Bit1:
Additional information about the PDUs received is to be entered in
_N_SIEMDOMAINSEQ_MPF for download
Machine data
3.2 General machine data
Parameter Manual
64 Parameter Manual, 08/2015, 6FC5397-8EP40-0BA1

Siemens SINUMERIK 808D ADVANCED Specifications

General

Brand	Siemens
Model	SINUMERIK 808D ADVANCED
Category	Control Unit
Language	English