450
When [Adaptive Y] or [Adaptive Y/C] is selected, set the
following parameter.
a) 1: Mode with highest proportion converted from frames (still picture
priority mode)
2: Mode with higher proportion converted from frames
3: Mode with higher proportion converted from fields
4: Mode with highest proportion converted from fields (motion priority
mode)
To set the up-converter conversion mode
In the <Conversion> group, select the conversion mode.
Frame: Conversion in frame units
Field: Conversion in field units
Adaptive: Detects motion in the signal, and automatically
switches mode between conversion using frame units
and field units.
When [Adaptive] is selected, set the following parameter.
a) 1: Mode with highest proportion converted from frames (still picture
priority mode)
2: Mode with higher proportion converted from frames
3: Mode with higher proportion converted from fields
4: Mode with highest proportion converted from fields (motion priority
mode)
To return the conversion method settings to the
defaults
Press [Default]. The settings for the selected FC channels
are reset to the defaults.
Setting the frame delay
You can set the input signal delay level for each FC
channel.
1
In the Engineering Setup >Switcher >Input >Internal
FC menu (7332.5), select the target FC channel to set.
2
Set the following parameter.
a) The following delay levels can be configured, depending on the
switcher signal format.
3840×2160P, 1080P: 1 to 15 frames
3840×2160PsF, 1080PsF, 1080i: 1 to 8 frames
720P: 1 to 15 frames (set value of 1 to 8 frames when the conversion
format is 1080i/576i/480i, with an actual delay that is double the set
value)
Setting the frame synchronizer
You can enable/disable the frame synchronizer for each
FC channel. When the frame synchronizer is enabled,
unsynchronized input signals are synchronized.
The frame synchronizer cannot be enabled in the following
cases.
• When the switcher signal format is 3840×2160P or
3840×2160PsF
• When the switcher signal format is 1080P and the 720P
converter is enabled
1
In the Engineering Setup >Switcher >Input >Internal
FC menu (7332.5), select the target FC channel to set.
2
Press [Frame Sync] to enable/disable the frame
synchronizer.
To enable, press [Frame Sync], turning it on. To
disable, press [Frame Sync], turning it off.
Setting an Input Format Converter
You can set an input format converter, frame delay, and
frame synchronizer for primary inputs of the following
input connector boards.
• XKS-S8111 SDI Input and FC Connector Board
• XKS-S8112/XKS-S9112 12G-SDI Input Boards
• XKS-C8111/XKS-C9111 100G IP Input Boards
• XKS-C9121 100G IP Input and Output Board
The XKS-C8111/XKS-C9111/XKS-C9121 have the
following restrictions.
• The input format converter setting is available only
when the switcher signal format is 3840×2160P 2SI or
1080P.
• On the XKS-C8111, an input format converter can be
configured on only the 1st to 4th inputs of each board.
• On the XKS-C9111/XKS-C9121, when the switcher
signal format is 3840×2160P 2SI, an input format
converter can be configured on only the 1st & 2nd and
9th & 10th inputs of each board.
• On the XKS-C9111/XKS-C9121, when the switcher
signal format is 1080P, an input format converter can be
configured on only the 1st to 4th and 9th to 12th inputs
of each board.
• Frame synchronizer is disabled.
No. Parameter Adjustment
2Motion
Select
Motion detection sensitivity
a)
No. Parameter Adjustment
2Motion
Select
Motion detection sensitivity
a)
No. Parameter Adjustment
3Frame
Delay
Delay level
a)
Note
Note
To Next Page
Loading...
Need help?
General
