SystemAir Geniox 12 User Manual

15-1
| Short description of main components in the control system
Annex 15 Short description of main components in the control system
15.1 Geniox units delivered in several sections
This model of the Geniox unit has an integrated control system and depending on the size of the unit, the cabinet is
installed on the unit or on the front of the unit. The 2 controllers - Systemair E283W–3 port controller and a Systemair
E28 expansion - both controllers are mounted in the cabinet, and all electrical connections between cabinet and
components in the unit are installed. The control system is configured according to the customer’s order – confirmed by
the order confirmation - to promote easy start-up on the site. The unit is tested at the factory and all functions are
confirmed by a final functional test and test report. The test report is annex 14 for the User Manual. After the final test
the unit is divided in sections to facilitate the transport. After reassembly of the unit on the site, the clearly marked
cables with sockets must be reconnected in the marked cabinet terminals. Cable strips are preinstalled for installation
of the cables between the components in the unit-sections and the cabinet. Cables installed on the unit-sections in the
preinstalled strips are protected by metal covers. The covers have been removed before installation of the unit on the
final site and must be replaced after installation of the cables. Cables with the mains power supply must be installed in
the automatic circuit breakers belonging to fans, heat pump unit GenioxU-HP (if delivered). All external components
must be connected on the site.
15.1.1 External components
External components are Systemair Control Panel, valves, valve motors, pressure transmitters, supply air temperature
sensor, sensor for water temperature in the heating coil (if water heating coil was requested) and circulation pump
(Systemair does not deliver the pump). Terminals are present in the cabinet for pressure transmitters, if it is a solution
for constant pressure in the ducts, and terminals are present in the cabinet for valve motors, circulation pump, supply
air temperature sensor and sensor for water temperature in the heating coil, but cables are not installed and not
connected to terminals in the cabinet. The Systemair Control Panel with 10 meters of cable is not connected to the
controller in the cabinet. All external components delivered are packed in a cardboard box delivered together with the
unit.
15.2 Geniox unit delivered assembled on base frame
This model of the Geniox unit has an integrated control system and the cabinet mounted inside the unit. The cabinet is
always mounted in the unit section with the heat exchanger and the cabinet is always placed at the warm side of the
heat exchanger. The intelligent controllers – Systemair E283W–3 port controller and a Systemair E28 expansion - both
controllers are mounted in the cabinet, and all electrical connections between cabinet and components in the unit are
installed. The control system is configured according to the customer’s order – confirmed by the order confirmation - to
promote easy start-up on the site. The unit is tested at the factory and all functions are confirmed by a final functional
test and test report. The test report is annex 14 for the User Manual. The unit is delivered as one assembled section on
base frame. Cables with the mains power supply must be installed in the automatic circuit breakers belonging to fans,
heat pump unit GenioxU-HP (if delivered). All external components must be connected on the site.
15.2.1 External components
External components are Systemair Control Panel, valves, valve motors, pressure transmitters, supply air temperature
sensor, sensor for water temperature in the heating coil (if water heating coil was requested) and circulation pump
(Systemair does not deliver the pump). Terminals are present in the cabinet for pressure transmitters, if it is a solution
for constant pressure in the ducts, and terminals are present in the cabinet for valve motors, circulation pump, supply
air temperature sensor and sensor for water temperature in the heating coil, but cables are not installed and not
connected to terminals in the cabinet. The Systemair Control Panel with 10 meters of cable is not connected to the
controller in the cabinet. All external components delivered are packed in a cardboard box delivered together with the
unit.
output |

SystemAir Geniox 12 Specifications

General

Brand	SystemAir
Model	Geniox 12
Category	Air Handlers
Language	English