Ecotech A Series User Manual

FRONT MATTER
98307600 Rev. C-1 1
Manual History
This manual is the combination of two previous versions which have now been
merged into one document to cater for the continuing development of the EC9800
series analyzers. The original manuals were:
• ML9830 Operation Manual , PN: 98300068, Rev. R, September 1998.
• ML9830B Operation Manual , PN: 98307005, Rev. K, December 1999.
The scope of this new manual covers the following analyzers:
• EC9830 Carbon Monoxide Analyzer, (A-Series), PN: 98301000-100.
• EC9830B Carbon Monoxide, (B-Series), PN: 98307000-1.
Both of the instruments are Manufactured by Ecotech P/L in Australia and support
the new (SMD) Microprocessor Board (Part number 98000063-4). This manual is
current for firmware version 1.11 and above.
Ecotech Manual ID:
#330.
Manual PN:
98307600.
Current Revision:
C-1.
Date Released:
November 2005.
Description:
EC9830 Carbon Monoxide Analyzer, Operation Manual, A & B Series.
Revision History
Rev Date Summary Affected Pages
A Jan 2004 New Release for new Microprocessor Board. A & B
series Combined. Based on original manuals.
All
B Feb 2004 Changes to menu options and structure. All
C June 2005 Changed to updated EC manual All
C-1 November
2005
New Calculation factors screen added 2-15, 2-29
NOTE: The photograph on the binder of this manual is of the south coast of Australia during Bushfires in 2003. The
photograph is courtesy of Earth Sciences and Image Analysis Laboratory, NASA Johnson Space Center. Photo
Reference: ISS006-E-19897.

Ecotech A Series Specifications

General

Brand	Ecotech
Model	A Series
Category	Measuring Instruments
Language	English

Summary

Manual History

Revision History

Details the revisions made to the manual, including dates and summaries of changes.

Notice

Mark Declaration and Conformity

Scope of Declaration

Defines the analyzer models covered by the declaration and lists compliance standards.

Internationally Recognized Symbols

Safety Requirements and Equipment Details

Equipment Rating

Specifies the electrical rating and environmental conditions for the analyzer.

Environmental Conditions

Details the acceptable relative humidity, temperature, and altitude for operation.

Factory Service and Support

Factory Service

Procedure for obtaining factory repair services and required information.

Service and Spare Parts

Contact information and services for customer support and spare parts.

Claims and Discrepancies

Claims for Damaged Shipments

Steps for reporting and claiming for damaged equipment upon receipt.

Shipping Discrepancies

Procedure for reporting shortages or discrepancies against the packing list.

Warning

1.0 Description of EC9830 Analyzer

1.1 Specifications

Detailed technical specifications including range, noise, drift, and performance metrics.

1.2 U.S. EPA Reference Method

Information on the EC9830's designation as a U.S. EPA reference method.

2.0 Installation and Operation

2.1 Mechanical Installation

Instructions for physical installation, including location and connections.

2.2 AC Power Connection

Steps for connecting the analyzer to AC power and display adjustments.

2.3 Operation

General procedures for operating the analyzer using the front panel controls.

2.4 Analyzer Calibration

Procedures for calibrating the analyzer to ensure accuracy.

2.5 Menus and Screens

Overview of the analyzer's menu structure and screen displays.

2.6 Analog Output

Configuration and connection of analog outputs for data recording.

2.7 Password Protection

How to enable and use password protection for configuration settings.

3.0 Calibration Procedures

3.1 Overview and Instructions

Introduction to calibration concepts and basic instructions.

3.2 Multipoint Calibration Procedures

Detailed methods for multipoint calibration using gas.

3.4 Automatic Zero/Span Checks (AZS)

Explanation and setup of automatic zero/span checks for calibration maintenance.

4.0 Digital Communication

4.1 Discrete Control

Using discrete I/O signals for analyzer control.

4.2 Serial Control

Using RS232 serial ports for communication.

4.4 Serial Command Control

Commands for controlling the analyzer via serial interface.

4.5 USB Communication

Connecting and communicating via USB.

4.6 EC9800 Communicator Software

Software for downloading data and remote control.