Honeywell APT4000PH User Manual

4
APT4000PH
Parameter set 1/2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60
Default settings of parameter sets . . . . . . . . . . . . . . . . . . . . . .61
Parameter set, individual settings . . . . . . . . . . . . . . . . . . . . . . .62
Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64
pH calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65
Zero adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66
Automatic calibration with Calimatic . . . . . . . . . . . . . . . . . . . .68
Manual calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70
Data entry of premeasured electrodes . . . . . . . . . . . . . . . . . . .72
Product calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74
ORP calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .76
Adjusting temp probe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .78
Measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .78
Diagnostics functions . . . . . . . . . . . . . . . . . . . . . . . . .79
Controller functions . . . . . . . . . . . . . . . . . . . . . . . . . . .82
PID controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .82
Pulse length / pulse frequency controller . . . . . . . . . . . . . . . . . .84
Connecting a rinsing system . . . . . . . . . . . . . . . . . . . .85
Operation with automatic cleaning system . . . . . . .85
Error messages (error codes) . . . . . . . . . . . . . . . . . . .86
Calibration error messages . . . . . . . . . . . . . . . . . . . . . . . . . . . .88
Operating states . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .90
Sensoface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .92
Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .94
Product line and accessories . . . . . . . . . . . . . . . . . . . . . . . . . . .94
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .95
Buffer tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .101
Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .108
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .112
Contents
5
Safety information
Be sure to read and observe the following instruc-
tions!
The analyzer has been designed in accordance with the state of
the art and complying with the applicable safety regulations.
When operating the analyzer, certain conditions may neverthe-
less lead to danger for the operator or damage to the analyzer.
Caution!
Commissioning may only be carried out by trained experts.
Whenever it is likely that protection has been impaired, the
analyzer shall be made inoperative and secured against unin-
tended operation.
The protection is likely to be impaired if, for example:
• the analyzer shows visible damage
• the analyzer fails to perform the intended measurements
• after prolonged storage at temperatures above 70 °C
• after severe transport stresses
Before recommissioning the analyzer, a professional routine test
in accordance with EN 61010-1 must be performed. This test
should be carried out by the manufacturer.
Caution!
Before commissioning it must be proved that the analyzer may
be connected with other equipment.

Honeywell APT4000PH Specifications

General

Brand	Honeywell
Model	APT4000PH
Category	Measuring Instruments
Language	English