To Next Page

To Previous Page

5 SERIAL NUMBERS

5.1 Vehicle identification number

401945-10

The vehicle identification number

is stamped on the right side

of the steering head.

5.2 Type label

401946-10

The type label

is fixed to the front of the steering head.

5.3 Engine number

H01047-10

The engine number

is embossed on the left side of the

engine above the engine sprocket.

5.4 Fork part number

401947-10

The fork part number

is stamped on the inner side of the fork

stub.

Default Chapter4
- Table of Contents4
1 Means of Representation 17
- Symbols Used7
- Formats Used7
2 Safety Advice8
- Use Definition - Intended Use8
- Misuse8
- Degrees of Risk and Symbols8
- Tampering Warning9
- Safe Operation9
- Protective Clothing10
- Work Rules10
- Environment10
- Owner's Manual10
3 Important Notes12
- Manufacturer Warranty, Implied Warranty12
- Fuel, Auxiliary Substances12
- Spare Parts12
- Husqvarna Motorcycles Technical Accessories12
- Service12
- Figures12
- Customer Service13
4 View of Vehicle14
- View of Vehicle, Front Left (Example)14
- View of Vehicle, Rear Right (Example)15
5 Serial Numbers16
- Vehicle Identification Number16
- Type Label16
- Engine Number16
- Fork Part Number16
- Shock Absorber Article Number17
6 Controls18
- Clutch Lever18
- Hand Brake Lever18
- Throttle Grip18
- Stop Button18
- Map Switch19
- Start Button19
- Overview of Indicator Lights19
- Opening Fuel Tank Filler Cap19
- Closing the Fuel Tank Filler Cap20
- Opening 2-Stroke Oil Tank Cap20
- Closing 2-Stroke Oil Tank Cap21
- Cold Start Button21
- Idle Speed Adjusting Screw21
- Shift Lever22
- Foot Brake Lever22
- Side Stand22
- Service Hour Counter23
7 Preparing for Use24
- Preparing for Use24
- Advice on Preparing for First Use24
- Running in the Engine25
- Starting Power of Lithium-Ion Batteries at Low Temperatures25
- Preparing the Vehicle for Difficult Operating Conditions26
- Preparing the Vehicle for Riding on Dry Sand26
- Preparing the Vehicle for Riding on Wet Sand27
- Preparing the Vehicle for Riding on Wet and Muddy Circuits28
- Preparing Vehicle for High Temperatures or Slow Riding29
- Preparing the Vehicle for Low Temperatures or Snow30
8 Riding Instructions 831
- Checks and Maintenance Measures When Preparing for Use31
- Starting the Vehicle31
- Starting off32
- Shifting, Riding32
- Applying the Brakes33
- Stopping, Parking33
- Transporting34
- Refueling35
- Adding 2-Stroke Oil36
9 Service Schedule 937
- Additional Information37
- Required Work37
- Recommended Work38
10 Tuning the Chassis40
- Checking the Basic Chassis Setting with the Rider's Weight40
- Air Suspension XACT 544840
- Compression Damping of the Shock Absorber41
- Adjusting the Low-Speed Compression Damping of the Shock Absorber41
- Adjusting the High-Speed Compression Damping of the Shock Absorber42
- Adjusting the Rebound Damping of the Shock Absorber42
- Measuring the Rear Wheel Dimension Unloaded43
- Checking the Static Sag of the Shock Absorber44
- Checking the Riding Sag of the Shock Absorber44
- Adjusting the Spring Preload of the Shock Absorber45
- Adjusting the Riding Sag46
- Checking the Basic Setting of the Fork46
- Adjusting the Fork Air Pressure47
- Adjusting the Compression Damping of the Fork48
- Adjusting the Rebound Damping of the Fork48
- Handlebar Position49
- Adjusting the Handlebar Position49
11 Service Work on the Chassis 1151
- Raising the Motorcycle with a Lift Stand51
- Removing the Motorcycle from the Lift Stand51
- Bleeding the Fork Legs51
- Cleaning the Dust Boots of the Fork Legs52
- Removing the Fork Protector53
- Installing the Fork Protector53
- Removing the Fork Legs53
- Installing the Fork Legs54
- Removing the Lower Triple Clamp55
- Installing the Lower Triple Clamp56
- Checking Steering Head Bearing Play58
- Adjusting Steering Head Bearing Play59
- Lubricating the Steering Head Bearing59
- Removing the Start Number Plate60
- Installing the Start Number Plate60
- Removing Front Fender60
- Installing Front Fender61
- Removing the Shock Absorber61
- Installing the Shock Absorber63
- Removing the Seat64
- Mounting the Seat65
- Removing the Air Filter Box Cover65
- Installing the Air Filter Box Cover65
- Removing the Air Filter66
  - Cleaning the Air Filter and Air Filter Box66
  - Installing the Air Filter67
  - Removing the Main Silencer68
  - Installing the Main Silencer68
  - Changing the Glass Fiber Yarn Filling of the Main Silencer68
  - Removing the Right Side Cover69
  - Installing the Right Side Cover70
  - Removing the Fuel Tank70
  - Installing the Fuel Tank72
  - Checking the Chain for Dirt73
  - Cleaning the Chain73
  - Checking the Chain Tension74
  - Adjusting the Chain Tension75
  - Checking the Chain, Rear Sprocket, Engine Sprocket, and Chain Guide76
  - Checking the Frame78
  - Checking the Link Fork78
  - Checking the Throttle Cable Routing78
  - Checking the Rubber Grip79
  - Adjusting the Basic Position of the Clutch Lever80
  - Checking/Correcting the Fluid Level of Hydraulic Clutch80
  - Changing the Hydraulic Clutch Fluid81
12 Brake System 1283
- Adjusting the Basic Position of the Hand Brake Lever83
- Checking the Brake Discs83
- Checking the Front Brake Fluid Level84
- Adding Front Brake Fluid84
- Checking the Front Brake Linings85
- Changing the Brake Linings of the Front Brake86
- Checking the Free Travel of Foot Brake Lever88
- Adjusting the Basic Position of the Foot Brake Lever89
- Checking the Rear Brake Fluid Level89
- Adding Rear Brake Fluid90
- Checking the Brake Linings of the Rear Brake91
- Changing the Rear Brake Linings91
13 Wheels, Tires94
- Removing the Front Wheel94
- Installing the Front Wheel95
- Removing the Rear Wheel95
- Installing the Rear Wheel96
- Checking the Tire Condition98
- Checking Tire Pressure98
- Checking Spoke Tension99
14 Electrical System100
- Removing the 12-V Battery100
- Installing the 12-V Battery101
- Charging the 12-V Battery101
- Changing Main Fuse103
- Changing the Fuses of Individual Electrical Power Consumers104
- Diagnostics Connector105
15 Cooling System106
- Checking the Antifreeze and Coolant Level106
- Checking the Coolant Level107
- Draining the Coolant107
- Refilling with Coolant108
- Changing the Coolant110
16 Tuning the Engine112
- Checking the Play in the Throttle Cable112
- Adjusting the Play in the Throttle Cable112
- Adjusting the Characteristic Map of the Throttle Response113
- Adjusting the Idle Speed114
- Programming Ambient Air Pressure115
- Checking the Basic Position of the Shift Lever115
- Adjusting the Basic Position of the Shift Lever116
17 Service Work on the Engine 17117
- Changing the Fuel Screen117
- Checking 2-Stroke Oil Level118
- Priming Oil Pump118
- Cleaning the Oil Screen in the Oil Tank120
- Checking the Gear Oil Level122
- Changing the Gear Oil123
- Adding the Gear Oil124
18 Cleaning, Care126
- Cleaning the Motorcycle126
19 Storage128
- Preparing for Use after Storage129
20 Troubleshooting130
21 Blink Code132
22 Technical Data134
- Engine134
- Engine Tightening Torques134
- Capacities136
- Gear Oil136
- Coolant136
- Fuel136
- Chassis136
- Electrical System137
- Tires137
- Fork137
- Shock Absorber138
- Chassis Tightening Torques138
23 Substances 23141
24 Auxiliary Substances 24143
25 Standards 25145
26 Index of Special Terms146
27 List of Abbreviations 27147
28 List of Symbols148
- Red Symbols148
- Yellow and Orange Symbols148
- Index149

Brand	Husqvarna
Model	TX 300i 2022
Category	Motorcycle
Language	English

Husqvarna TX 300i 2022 User Manual

Table of Contents

Questions and Answers:

Husqvarna TX 300i 2022 Specifications

Related product manuals