MAINTENANCE BASICS
7-10
TABLE OF LUBRICANTS AND OPERATING
AGENTS
WA75-3
LUBRICANTS AND OPERATING AGENTS BI-CODES*),
SPECIFICATIONS, AND FILLING VOLUMES
Lubricants
and Service
Fluids
BI-Codes
Quality
Classes
Temperature
Ranges
Viscosity
Classes
Filling Vol-
ume in Litres
approx.
Engine Engine Oil EO EO 1540 A
EO 1030 A NRS
CCMC D4 or, if not
available: API CE or
API CF-4²)
-15° to 45° C
-20° to 30° C
-15° to 20° C
SAE 15W-40 ¹)
SAE 10W-30
SAE 05W-30
9.4
Transfer Gear Box:
Standard Type
High Speed Version
Gear Oil GO GO 90 LS API-GL5 +LS or
MIL-L-2105D+LS
- SAE 90LS
1.0
3.0
Front Axle Gear Oil GO GO 90 LS API-GL5 +LS
or
MIL-L-2105D+LS
- SAE 90 LS ¹)
SAE 85W-90LS
SAE 80W-90LS
Planet Gear: 2 x 0.9
Differential: 4.3
Rear Axle Gear Oil GO GO 90 LS API-GL5 +LS
or
MIL-L-2105D+LS
- SAE 90 LS ¹)
SAE 85W-90LS
SAE 80W-90LS
Planet Gear: 2 x 0.9
Differential: 4.7
Hydraulic
System,
Steering
Hydraulic Oil HYD HYD 0530
HYD 1030
HYD 1540
HVLP
HVLP D
15° to 20° C
-20° to 30° C
-15° to 45° C
ISO VG 46 ¹)
ISO VG 68
ISOVG100
95
or
Engine Oil EO
EO 1540 A
EO 1030 A
NRS
CCMC D4 or,
if not available:
API CE or
API CF -4²)
-15° to 45° C
-20° to 30° C
-15° to 20° C
SAE 15W-40 ¹)
SAE 10W-30
SAE 05W-30
or
Hydraulic Oil
BIO-E-HYD
BIO-E-HYD 0530 HEES
(acc. to VDMA fluid
technology)
-15° to 20° CISOVG46
Service Brake Automatic Transmis-
sion Gear Oil
ATF ATF, Type A,
Suffix A
--0.6
Cooling System Long-Time
Coolant
SP-C Antifreeze and
Corrosion
Protection
Proportion of Mixture:
50% Coolant: 50% Water
Min. Freeze Proofing: -34° C
12.25
Fuel Tank Diesel Fuel³) CFPP Class B
CFPP Class D
CFPP Class E
CFPP Class F
DIN-EN 590 up to 0°C
up to -10°C
up to -15°C
up to -20°C
90
Grease Nipple Lithiumsoap-Based
Multi-Purpose Grease
MPG-A KP2N-20 - NLGI 2
Air conditioning Coolant
Refrigerating
machine oil
NRS
NRS
R134a (CFC-free)
PAG
(Polyalkyleneglycol)
1200 g
180 cm³
The specified filling volumes represent approximate values; the testing devices are binding. The selection of a viscosity class depends on the ambient temperature prevailing over a
longer period of time. The temperature limits are to be regarded as guiding values; for a brief period, the actual temperature may be higher or lower than these guiding values.
¹)Factory filling
²) If engine oil of either the API CE or the API CF - 4 specification is not available, engine oil of either the API CC or the API CD specification may be used. In these cases, the oil change
intervals must be cut in halves.
³) If fuels with a sulphur content between 0.5 and 1.0 % are used, the oil change intervals for the engine must be cut in halves; if the sulphur content exceeds 1.0 %, the oil change inter-
vals must be quartered.
*) BI-codes are the "standard lubricants" (Regelschmierstoffe) for construction machinery and vehicles of the Hauptverband der Deutschen Bauindustrie e.V. (BI) (head association of
the German construction industry). The brochure "Regelschmierstoffe für Baumaschinen- und Fahrzeuge" (standard lubricants for construction machinery and vehicles" can be
obtained from bookstores or the German Bauverlag GmbH Wiesbaden und Berlin under the ISBN-No. 3-7625-3102-1.
To Next Page
Loading...
Need help?
General
