44205401TH Rev.1
92 /
Oki Data CONFIDENTIAL
5. Maintenance Menu
5.1 System maintenance menu (for maintenance engineer)
While pressing the MENU+ and MENU- keys, turn on the power to enter the maintenance menu.
The menu indications are shown in English only regardless of the destination of the printer.
Note! The system maintenance menu is internally use only, and should not be
disclosed to end user because destination and other parameters can be
modified using this menu.
Table 5-1 Maintenance menu function table
Category
Item
(1st Line)
Value
(2nd Line)
DF Function
System
Mainte-
nance
Enter
Password
******
******
000
000
Enter the password to enter the system maintenance
menu.
Default value is "000000".
A password can be entered in the range of 6- to
12-digit alphanumeric.
For more details, refer to the "Password" sheet.
OKIUSER OKIUSER ODA
OEL
APS
JP1
JPOEM1
OEMA
OEML
*
Set the destination.
JPOEM1: Japanese OEM
OEMA: Overseas OEM outside J
apan of A4 size
default
OEMA: Overseas OEM outside Japan of the
Letter siz
e default
When the printer exits the menu, the printer reboots
automatically.
Mainte-
nance
Menu
[Display condition]
Encrypted SD Memory Card function is disabled.
Format SD
Card
Execute - IInitializes an SD card. Pressing the Enter button for
this option displays the confirmation message:
Are You Sure?
Yes
No
Selecting No restores the last menu view. Selecting
Yes exits the menu, starting formatting an SD card
installed in the printer.
[Display condition]
The printer has an SD Card (Boot Menu-Storage
Setup-Enable SD Card is set to Yes).
* With Boot Menu-Storage Setup-Enable Initialization
set to Yes, the option can be displayed.
Category
Item
(1st Line)
Value
(2nd Line)
DF Function
Mainte-
nance
Menu
Format
Flash ROM
Execute - Initializes flash ROM. Pressing the Enter button for
this option displays the confirmation message:
Are You Sure?
Yes
No
Selecting No restores the last menu view. Selecting
Yes exits the menu, starting formatting an (on-board)
flash device resident in the printer.
* Never use the option.
Reset
EEPROM
Execute - Returns the EEPROM contents to the setup by the
manufacturer when shipped from the factory (factory
default profile) value. Upon completion of the setting
change, the system reboots automatically.
* Some specific items are not initialized.
Mainte-
nance Print
Menu
Mainte-
nance Print
Menu
Enable
Disable
*
Selects whether or not to display "Print Information"
- "ID Check Pattern" and "Engine Status".
When this menu item is set to "Disable", the function
menu "Print Information" - ID Check Pattern" and
"Engine Status" are not displayed all the time.
When exiting this menu upon completion of setting
change, the printer reboots automatically.
Fuse Keep
Mode
Fuse Keep
Mode
Execute - When the ENTER key is pressed, the command is
issued from CU to PU to set the system in ON LINE.
Replace the consumable part with the new part
while the power is turned on. (In this case, fuse
of the new consumable part is not cut, and the
operational counts are reset so that the count value
of old consumable part is not added.)
The check mode is terminated when the power is
turned off. The check mode is disabled when the
power is turned on next time.
Personality XPS Enable
Disable
* Changes the default of Support PDL per brand.
PDL which is "Disable" in this menu is not displayed
at "Print Setup" - "Personality" of Function menu.
INVALID DATA shows up and received data is
abandoned when print data of PDL which is
"Disable" is received.
IBM 5577 Enable
Disable
*
IBM PPR III
XL
Enable
Disable
*
EPSON FX Enable
Disable
*
HP-GL/2 Enable
Disable
*
To Next Page
Loading...
Need help?
General
